problem with bridging!!! :(


 
Thread Tools Search this Thread
Special Forums IP Networking problem with bridging!!! :(
# 1  
Old 08-07-2009
problem with bridging!!! :(

Hello,
I have an UTM [Unified Thread Management] that has 4 ports. I was bridged two ports of it. my pc wired to one port and other one to network. Now I can ping my default gateway but it doesn't work(I haven't access to internet) even http of gateway, what happened? what route I should added?
Thanks in advance.Smilie
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Programming

Bridging Talk

Hi! I would like to start creating a bridge for good old Unix talk program. This bridge would allow you to joinIRC-channel by using talk just for example. I have a couple of questions: 1. Are there any previous attempts or implementations creating Talk bridge? 2. Which version of the talk... (9 Replies)
Discussion started by: homebeach
9 Replies

2. IP Networking

Router problem or ISP problem ?

Hi everyone, I am experiencing discontinuity of Internet service, this started 1 month ago. Everything worked very well for 1 year of intensive use, but now, I have problems reaching my gateway. The gateway is not my router but a node belonging to my ISP and I share the same public IP with... (3 Replies)
Discussion started by: remic
3 Replies

3. UNIX for Dummies Questions & Answers

sed Or Grep Problem OR Terminal Problem?

I don't know if you guys get this problem sometimes at Terminal but I had been having this problem since yesterday :( Maybe I overdid the Terminal. Even the codes that used to work doesn't work anymore. Here is what 's happening: * I wanted to remove lines containing digits so I used this... (25 Replies)
Discussion started by: Nexeu
25 Replies

4. IP Networking

Linux Bridging, Wireless AP, IPv6 multicast and autoconfiguration.

Well I cannot be too certain of the setup, since it's a stock firmware, but I have a cheap Belkin wireless-n router and wanted to get some ideas of what may be going on while I've a few moments to ramble on about my problems... I requested the GPL source so I've just been pondering while waiting to... (0 Replies)
Discussion started by: neutronscott
0 Replies

5. Solaris

openindiana bridging problem (brctl)

Hello all, I was trying to hooking up several computers into my openindiana server box, the server box has few RJ45 gigabit ethernet. The desired hierarchy of the network will be shown as on the picture attached. I would like to connect each host into my gigabit ethernet because of me and my... (2 Replies)
Discussion started by: enno
2 Replies

6. IP Networking

Problem with forwarding emails (SPF problem)

Hi, This is rather a question from a "user" than from a sys admin, but I think this forum is apropriate for the question. I have an adress with automatic email forwarding and for some senders (two hietherto), emails are bouncing. This has really created a lot of problems those two time so I... (0 Replies)
Discussion started by: carwe
0 Replies

7. AIX

AIX OS problem? network problem?

Dear ALL. I installed AIX OS on customer sites. but Only one site is too slow when I connected telnet, ftp.. Ping is too fast. but telnet and FTP is not connected.. of course i check the configuration file on aix but it's normal. Do any Idea?? thanks in advance. - Jun - (3 Replies)
Discussion started by: Jeon Jun Seok
3 Replies

8. AIX

user login problem & Files listing problem.

1) when user login to the server the session got colosed. How will resolve? 2) While firing the command ls -l we are not able to see the any files in the director. but over all view the file system using the command df -g it is showing 91% used. what will be the problem? Thanks in advance. (1 Reply)
Discussion started by: pernasivam
1 Replies

9. UNIX for Advanced & Expert Users

Bridging with SSH Tunnels

Here is the scenario: I use an OpenBSD 2.9 box as my firewall and gateway at the house. One of the boxes behind my OpenBSD box is my FreeBSDBox. I would like to be able to use port forwarding with SSH to enable a secure connection from work to the OpenBSD box and to have the OpenBSD box... (6 Replies)
Discussion started by: auswipe
6 Replies
Login or Register to Ask a Question
natutil(8)						    BSD System Manager's Manual 						natutil(8)

NAME
natutil -- Query and configure supported Network Address Translation (NAT) devices SYNOPSIS
natutil [-vx] [-a auth] [-n name] {-1 | -d | -m | -s | -i | -L} natutil [-vx] [-a auth] [-n name] {-t | -u} {-T | -U} -p ports DESCRIPTION
natutil uses the ACP protocol to detect, configure, and extract status information from Internet gateway devices (IGDs) (such as AirPort Base Stations) on the local network. Since most IGDs provide Network Address Translation (NAT) service, they are often interchangably referred to as "NAT devices" or simply "NATs". The first synopsis line (with the exception of -L) returns various information from NAT devices. The second invocation modifies settings on the device. After modifying settings, AirPort Base Stations must be rebooted for the changes to take effect. ( servermgrd(8) also reboots the AirPort Base Station when it modifies port mappings.) OPTIONS
The following options / commands are available: -1 Only return data if the IGD found is also our current gateway. [AirPort only] Will only return if this base station can be autocon- figured -a auth [AirPort only] The authentication string to use when communicating with a device protected with a password other than the default "public". Used mostly for scripted operation. Use -i to get the authentication string interactively. -i Get the authentication string interactively. This preferred over -a for security reasons. -d Reports the IGDs (Internet Gateway Devices) that were found during the discovery. -m Retrieves the port mapping table from the NAT. -n name The prefix of the targeted NAT device's name (useful in a LAN with multiple NAT devices). -p ports A comma-separated list of the ports to tap or untap. Must be used with -t or -u. -s Retrieves the WAN & LAN status and configuration from the IGD. -t Configures the NAT to forward the given ports to this machine. Requires -p and either -T or -U. -u Removes the given ports from the NAT's port forwarding rules. Requires -p and either -T or -U. -v Verbose output. Provides progress and status information on standard output. -x XML output. This option provides the most information. -L [AirPort only] Convert existing DHCP lease into a static reservation so the host will receive the same IP address after each reboot. -T Ports will be tapped / untapped for the TCP protocol. Must be used with -t or -u. -U Ports will be tapped / untapped for the UDP protocol. Must be used with -t or -u. SEE ALSO
ifconfig(8), ipconfig(8) Mac OS X Server 10.5 July 23, 2007 Mac OS X Server 10.5