Hello,
I have an UTM [Unified Thread Management] that has 4 ports. I was bridged two ports of it. my pc wired to one port and other one to network. Now I can ping my default gateway but it doesn't work(I haven't access to internet) even http of gateway, what happened? what route I should added?
Thanks in advance.
Hi! I would like to start creating a bridge for good old Unix talk program. This bridge would allow you to joinIRC-channel by using talk just for example. I have a couple of questions:
1. Are there any previous attempts or implementations creating Talk bridge?
2. Which version of the talk... (9 Replies)
Hi everyone,
I am experiencing discontinuity of Internet service, this started 1 month ago. Everything worked very well for 1 year of intensive use, but now, I have problems reaching my gateway.
The gateway is not my router but a node belonging to my ISP and I share the same public IP with... (3 Replies)
I don't know if you guys get this problem sometimes at Terminal but I had been having this problem since yesterday :( Maybe I overdid the Terminal. Even the codes that used to work doesn't work anymore.
Here is what 's happening:
* I wanted to remove lines containing digits so I used this... (25 Replies)
Well I cannot be too certain of the setup, since it's a stock firmware, but I have a cheap Belkin wireless-n router and wanted to get some ideas of what may be going on while I've a few moments to ramble on about my problems... I requested the GPL source so I've just been pondering while waiting to... (0 Replies)
Hello all,
I was trying to hooking up several computers into my openindiana server box, the server box has few RJ45 gigabit ethernet. The desired hierarchy of the network will be shown as on the picture attached. I would like to connect each host into my gigabit ethernet because of me and my... (2 Replies)
Hi,
This is rather a question from a "user" than from a sys admin, but I think this forum is apropriate for the question.
I have an adress with automatic email forwarding and for some senders (two hietherto), emails are bouncing. This has really created a lot of problems those two time so I... (0 Replies)
Dear ALL.
I installed AIX OS on customer sites.
but Only one site is too slow when I connected telnet, ftp..
Ping is too fast. but telnet and FTP is not connected..
of course i check the configuration file on aix but it's normal.
Do any Idea??
thanks in advance.
- Jun - (3 Replies)
1) when user login to the server the session got colosed. How will resolve?
2) While firing the command ls -l we are not able to see the any files in the director. but over all view the file system using the command df -g it is showing 91% used. what will be the problem?
Thanks in advance. (1 Reply)
Here is the scenario:
I use an OpenBSD 2.9 box as my firewall and gateway at the house. One of the boxes behind my OpenBSD box is my FreeBSDBox.
I would like to be able to use port forwarding with SSH to enable a secure connection from work to the OpenBSD box and to have the OpenBSD box... (6 Replies)
aconnect(1) General Commands Manual aconnect(1)NAME
aconnect - ALSA sequencer connection manager
SYNOPSIS
aconnect [-d] [-options] sender receiver
aconnect -i|-o [-options]
aconnect -x
DESCRIPTION
aconnect is a utility to connect and disconnect two existing ports on ALSA sequencer system. The ports with the arbitrary subscription
permission, such as created by aseqview(1), can be connected to any (MIDI) device ports using aconnect. For example, to connect from port
64:0 to 65:0, run as follows:
% aconnect 64:0 65:0
The connection is one-way, and the whole data to the sender port (64:0) is redirected to the receiver port (65:0). When another port (e.g.
65:1) is attached to the same sender port, the data is sent to both receiver ports. For disconnection, use -d option.
% aconnect -d 64:0 65:0
The address can be given using the client's name.
% aconnect External:0 Emu8000:1
Then the port 0 of the client matching with the string "External" is connected to the port 1 of the client matching with the "Emu8000".
Another function of aconnect is to list the present ports on the given condition. The input ports, which may become sender ports, can be
listed with -i option.
% aconnect -i
client 0: 'System' [type=kernel]
0 'Timer '
1 'Announce '
client 64: 'External MIDI-0' [type=kernel]
0 'MIDI 0-0 '
Similarly, to see the output ports, use -o flag.
You can remove all existing exported connections using -x option. This function is useful for terminating the ALSA drivers, because the
modules with sequencer connections cannot be unloaded unless their connections are removed.
OPTIONS
CONNECTION MANAGEMENT
-d, --disconnect
Disconnect the given subscription.
-e, --exclusive
Connect ports with exclusive mode. Both sender and receiver ports can be no longer connected by any other ports.
-r, --real queue
Convert time-stamps of event packets to the current value of the given real-time queue. This is option is, however, not so useful,
since the receiver port must use (not necessarily own) the specified queue.
-t, --tick queue
Like -r option, but time-stamps are converted to the current value of the given tick queue.
LIST PORTS
-i, --input
List existing input (readable) ports. This option is exclusive to -o.
-o, --output
List existing output (writable) ports. This option is exclusive to -i.
-l, --list
List the current connection status. The connected and connecting ports from/to each port are listed together. The suffix flag [ex]
means the connection is exclusive. The suffix flag [real:#] and [tick:#] mean the connection includes real-time and tick conversion
on the listed queue, respectively.
REMOVE ALL CONNECTIONS
-x, --removeall
Remove all exported connections.
SEE ALSO aseqnet(1), aseqview(1)AUTHOR
Takashi Iwai <tiwai@suse.de>
August 31, 2000 aconnect(1)
08-07-2009
