10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
Is there a way to find out all the ports open between source IP & destination IP in any way ? (12 Replies)
Discussion started by: UnknownGuy
12 Replies
2. UNIX for Advanced & Expert Users
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
3. Shell Programming and Scripting
Hi Guys,
how to count number of files successfully copied while coping files from source to destination path
ex:10 files from source to target location copying
if 8 files copied successfully then
echo successfully copied=8
failure=2 files
if two files get error to coping files from... (23 Replies)
Discussion started by: sravanreddy
23 Replies
4. UNIX for Advanced & Expert Users
hi All,
i have 2 server setup now for Rsync, i configured Rsync on both of the server and it worked well when i did run from source to destination. and while running back from destination to source it produced this error:
bash-3.2$ ksh rsync_bravo_db.ksh usa0300uz1247.apps.mc.xerox.com... (0 Replies)
Discussion started by: lovelysethii
0 Replies
5. Linux
I'd like to specify a different build and deployment path for files, by default the same path is used for both build and install, I wasn't able to find a way to make these different. With Solaris pkgadd, one can specify different paths in prototype, so I would assume something like that is possible... (0 Replies)
Discussion started by: tiburblium
0 Replies
6. Shell Programming and Scripting
Move all files starting with a specific name to different directory.
This shell script program should have three parameters
File Name
Source Directory
Destination Directory
User should be able to enter ‘AB_CD*' in file name parameter. In this case all the files starting with AB_CD will... (1 Reply)
Discussion started by: chetancrsp18
1 Replies
7. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
8. IP Networking
Hi all,
How an interface is selected based on the destination ip address.
Thanks in advance........ (5 Replies)
Discussion started by: vijaypdp2006
5 Replies
9. Shell Programming and Scripting
Hi, need help how to count unique destination for the source ip. The file is contains 4 number of fields. Example of the file is here
src ip dest ip #of flows total bytes
192.168.6.0 88.0.33.2 12 128
192.168.6.0 88.0.33.2 1 168
192.168.6.0 ... (5 Replies)
Discussion started by: new_buddy
5 Replies
10. UNIX for Advanced & Expert Users
is there a command in unix/linux that allows you to sample what the historic byte rate is from a local IP to a client IP. (1 Reply)
Discussion started by: cubs0729
1 Replies
RDS-PING(1) BSD General Commands Manual RDS-PING(1)
NAME
rds-ping -- test reachability of remote node over RDS
SYNOPSIS
rds-ping [-c count] [-i interval] [-I local_addr] remote_addr
DESCRIPTION
rds-ping is used to test whether a remote node is reachable over RDS. Its interface is designed to operate pretty much the standard ping(8)
utility, even though the way it works is pretty different.
rds-ping opens several RDS sockets and sends packets to port 0 on the indicated host. This is a special port number to which no socket is
bound; instead, the kernel processes incoming packets and responds to them.
OPTIONS
The following options are available for use on the command line:
-c count
Causes rds-ping to exit after sending (and receiving) the specified number of packets.
-I address
By default, rds-ping will pick the local source address for the RDS socket based on routing information for the destination address
(i.e. if packets to the given destination would be routed through interface ib0, then it will use the IP address of ib0 as source
address). Using the -I option, you can override this choice.
-i timeout
By default, rds-ping will wait for one second between sending packets. Use this option to specified a different interval. The timeout
value is given in seconds, and can be a floating point number. Optionally, append msec or usec to specify a timeout in milliseconds
or microseconds, respectively.
Specifying a timeout considerably smaller than the packet round-trip time will produce unexpected results.
AUTHORS
rds-ping was written by Olaf Kirch <olaf.kirch@oracle.com>.
SEE ALSO
rds(7), rds-info(1), rds-stress(1).
BSD
Apr 22, 2008 BSD