10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
Is there a way to find out all the ports open between source IP & destination IP in any way ? (12 Replies)
Discussion started by: UnknownGuy
12 Replies
2. UNIX for Advanced & Expert Users
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
3. Shell Programming and Scripting
Hi Guys,
how to count number of files successfully copied while coping files from source to destination path
ex:10 files from source to target location copying
if 8 files copied successfully then
echo successfully copied=8
failure=2 files
if two files get error to coping files from... (23 Replies)
Discussion started by: sravanreddy
23 Replies
4. UNIX for Advanced & Expert Users
hi All,
i have 2 server setup now for Rsync, i configured Rsync on both of the server and it worked well when i did run from source to destination. and while running back from destination to source it produced this error:
bash-3.2$ ksh rsync_bravo_db.ksh usa0300uz1247.apps.mc.xerox.com... (0 Replies)
Discussion started by: lovelysethii
0 Replies
5. Linux
I'd like to specify a different build and deployment path for files, by default the same path is used for both build and install, I wasn't able to find a way to make these different. With Solaris pkgadd, one can specify different paths in prototype, so I would assume something like that is possible... (0 Replies)
Discussion started by: tiburblium
0 Replies
6. Shell Programming and Scripting
Move all files starting with a specific name to different directory.
This shell script program should have three parameters
File Name
Source Directory
Destination Directory
User should be able to enter ‘AB_CD*' in file name parameter. In this case all the files starting with AB_CD will... (1 Reply)
Discussion started by: chetancrsp18
1 Replies
7. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
8. IP Networking
Hi all,
How an interface is selected based on the destination ip address.
Thanks in advance........ (5 Replies)
Discussion started by: vijaypdp2006
5 Replies
9. Shell Programming and Scripting
Hi, need help how to count unique destination for the source ip. The file is contains 4 number of fields. Example of the file is here
src ip dest ip #of flows total bytes
192.168.6.0 88.0.33.2 12 128
192.168.6.0 88.0.33.2 1 168
192.168.6.0 ... (5 Replies)
Discussion started by: new_buddy
5 Replies
10. UNIX for Advanced & Expert Users
is there a command in unix/linux that allows you to sample what the historic byte rate is from a local IP to a client IP. (1 Reply)
Discussion started by: cubs0729
1 Replies
LO(4) BSD Kernel Interfaces Manual LO(4)
NAME
lo -- software loopback network interface
SYNOPSIS
device loop
DESCRIPTION
The loop interface is a software loopback mechanism which may be used for performance analysis, software testing, and/or local communication.
As with other network interfaces, the loopback interface must have network addresses assigned for each address family with which it is to be
used. These addresses may be set or changed with the SIOCSIFADDR ioctl(2). The loopback interface should be the last interface configured,
as protocols may use the order of configuration as an indication of priority. The loopback should never be configured first unless no hard-
ware interfaces exist.
If the transmit checksum offload capability flag is enabled on a loopback interface, checksums will not be generated by IP, UDP, or TCP for
packets sent on the interface.
If the receive checksum offload capability flag is enabled on a loopback interface, checksums will not be validated by IP, UDP, or TCP for
packets received on the interface.
By default, both receive and transmit checksum flags will be enabled, in order to avoid the overhead of checksumming for local communication
where data corruption is unlikely. If transmit checksum generation is disabled, then validation should also be disabled in order to avoid
packets being dropped due to invalid checksums.
DIAGNOSTICS
lo%d: can't handle af%d. The interface was handed a message with addresses formatted in an unsuitable address family; the packet was
dropped.
SEE ALSO
inet(4), intro(4)
HISTORY
The lo device appeared in 4.2BSD. The current checksum generation and validation avoidance policy appeared in FreeBSD 8.0.
BSD
March 15, 2009 BSD