10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
How to use 'ls' command to list files like *.dat, not *.*.dat (5 Replies)
Discussion started by: pmcginni777
5 Replies
2. Shell Programming and Scripting
I am trying to program a script that is using grep to find lines in a file in my home directory, and then use a pipe command to copy what is shown into different files in a different directory to create backup files. When I run it, though, it only creates a copy of the file that grep was going... (7 Replies)
Discussion started by: sammythesp3rmy
7 Replies
3. HP-UX
Good Day,
I've been trying to create a bootable recovery disk with no success. I've used the command ./make_recovery -A -d /dev/rmt/1m and get the command HP-UX System Recovery returned, and after about a minute an error is returned:
/var: write failed, file system is full... (26 Replies)
Discussion started by: Newnix
26 Replies
4. Infrastructure Monitoring
So i upgraded from Nagios version 2.6 to the latest version of nagios currently available.
but the problem is, i can't get the comments that were on my old version of nagios to show up on my new version of nagios.
has anyone else run into this issue?
the comments are extremely important.... (0 Replies)
Discussion started by: SkySmart
0 Replies
5. HP-UX
I have a make_recovery tape, if I restore the VG00 volume group using this, will my other volume groups still be ok after the restore(I have 7 data volume groups)
I used make_recovery -A to create the tape
I have a HP9000 HP-UX 11
An internal disk is failing, the other volume groups are on... (3 Replies)
Discussion started by: rees_a
3 Replies
6. AIX
I am trying to restore some files from a DLT drive in AIX 4.3 but I am having a few problems. Basically when I try to run the restore command I get the following error:
Cannot read from the specified input.
Please enter the device name when ready
I am the following command for the restore
... (0 Replies)
Discussion started by: The Hunter
0 Replies
7. HP-UX
I'm attempting to do a make_recovery on my HPUX box. My question revolves around the number of device files I have for my tape drive and what each one is intending for and which I should use. Some examples of my devices include 1m, 1mb, 1mnb, 2m, 2mb, 2mn, 2mnb, C1t0d0best, C1t0d0dds, &... (4 Replies)
Discussion started by: gonzotonka
4 Replies
8. Linux
HELP!!
I am having some major problems at present with a HP dat drive under RH9. The drive worked fine previously under RH8, but now does not work.
I am using kernel 2.4.20-30.9 on a i686 athlon intel box.
My messages log shows the below:
Apr 23 11:39:24 devsys kernel: ahc_pci:1:6:0:... (0 Replies)
Discussion started by: dkimber6
0 Replies
9. UNIX for Dummies Questions & Answers
okay.. pple..
say now i got an aix box. of course i could restore a backup done in aix environment.
1) now how about doing a restore from sun, hp from the aix box.?
2) can we install a sun, hp os into an aix box?
3) if (1) prohibits, then how about doing an sun, hp os installation on... (1 Reply)
Discussion started by: yls177
1 Replies
10. UNIX for Dummies Questions & Answers
hi, for aix and hpux, we have both mksysb and make_recovery for restoring to the former state after it was crashed. is there any equivalent to sun? any pointers will be appreciated. thanks (8 Replies)
Discussion started by: yls177
8 Replies
cmruncl(1m) cmruncl(1m)
NAME
cmruncl - run a high availability cluster
SYNOPSIS
cmruncl [-f] [-v] [-n node_name...] [-t | -w none]
DESCRIPTION
cmruncl causes all nodes in a configured cluster or all nodes specified to start their cluster daemons and form a new cluster.
To start a cluster, a user must either be superuser(UID=0), or have an access policy of FULL_ADMIN allowed in the cluster configuration
file. See access policy in cmquerycl(1m).
This command should only be run when the cluster is not active on any of the configured nodes. This command verifies the network configu-
ration before causing the nodes to start their cluster daemons. If a cluster is already running on a subset of the nodes, the cmrunnode
command should be used to start the remaining nodes and force them to join the existing cluster.
If node_name is not specified, the cluster daemons will be started on all the nodes in the cluster. All nodes in the cluster must be
available for the cluster to start unless a subset of nodes is specified.
Options
cmruncl supports the following options:
-f Force cluster startup without warning message and continuation prompt that are printed with the -n option.
-v Verbose output will be displayed.
-t Test only. Provide an assessment of the package placement without affecting the current state of the nodes or packages.
The -w option is not required with the -t option as -t does not validate network connectivity, but assumes that all the
nodes can meet any external dependencies such as EMS resources, package subnets, and storage.
-n node_name...
Start the cluster daemon on the specified subset of node(s).
-w none By default network probing is performed to check that the network connectivity is the same as when the cluster was config-
ured. Any anomalies are reported before the cluster daemons are started. The -w none option disables this probing. The
option should only be used if this network configuration is known to be correct from a recent check.
RETURN VALUE
cmruncl returns the following value:
0 Successful completion.
1 Command failed.
EXAMPLES
Run the cluster daemon:
cmruncl
Run the cluster daemons on node1 and node2:
cmruncl -n node1 -n node2
AUTHOR
cmruncl was developed by HP.
SEE ALSO
cmquerycl(1m), cmhaltcl(1m), cmhaltnode(1m), cmrunnode(1m), cmviewcl(1m), cmeval(1m).
Requires Optional Serviceguard Software cmruncl(1m)