10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi all,
I got following configuration problem
I need to configure tiny network on openbsd
I got server1 with 3 interfaces vic0 em0 em1
The interface vic0 on server1 has follwoing IP 172.16.1.1
em0
firstly I would like to configure network under em0 (I have assigned to em0 following... (1 Reply)
Discussion started by: kvok
1 Replies
2. Solaris
Hi everybody,
I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem.
I have 2 unix machines absolutely identical running solaris 9.
For network reasons I need to change the IP address of the 2 machines.
I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies
3. Solaris
Hi
I have installed Solaris 5.10 on Intel x86 machine (standalone).
I want to access internet through solaris. How should I configure the network? Is static IP or DHCP advisable? (5 Replies)
Discussion started by: johnl
5 Replies
4. UNIX for Dummies Questions & Answers
I am using solaris 10, my internet works alright but each time i reboot i keep loosing my connection. I will have to use the
ifconfig iprb0 192.168.1.xx netmask 255.255.255.0 up and
Route add default 192.168.1.xxx command to gain back my internet.
I know there is a better way of addressing... (1 Reply)
Discussion started by: seyiisq
1 Replies
5. SCO
I have a SCO 5.07 Server and I am trying to get it on my network. I have edited the /etc/hosts file and /etc/rc2.d/s99route . I has connectivity on the NIC card but not sure if I am forgetting another file. Thanks! (2 Replies)
Discussion started by: andrewd
2 Replies
6. UNIX for Dummies Questions & Answers
I need to know what commands I will need to use to change a host name, IP Address, and network configurations (routerings, dns, etc) and a Unix SCO machine.
Also, if there is any short tutorials on using the commands, i would defiently like that information.
Thanks!!! (1 Reply)
Discussion started by: HandleX
1 Replies
7. Solaris
hi again...
i configured my network settings sometiime ago using the sys-unconfig command.the active link was rtls0.
there was some problem with the network so i changed the ISP. now when im trying to reconfigure the system wit sys-unconfig, it tries to configure the network on rtls1 (and shows... (1 Reply)
Discussion started by: strider
1 Replies
8. HP-UX
Hi,
I have installed a HP-UX B.11.00 U 9000/800 Server in one of the domain. And I'm also able to telnet/ping into this server from systems in the same domain.
But I'm not able to telnet/ping into this server from a different domain.
So, what shoud need to do to achieve this... (6 Replies)
Discussion started by: S.Vishwanath
6 Replies
9. IP Networking
Hi,
I need to configure the Network for a Sun Solaris systems.
The OS info is SunOS Sparsh 5.8 Generic_108528-13 Sun4u Sparc SUNW,Ultra-250.
Please do let me know, how shall I shart with & more in configuring the Network.
Below is the list of Network Configuration I need to Make
... (2 Replies)
Discussion started by: S.Vishwanath
2 Replies
10. UNIX for Dummies Questions & Answers
Hi. I have installed Solaris 8 and I am trying to configure the network settings. For some reason every time I reboot, my card loses its configuration. I can run ifconfig and the only IP address bound to my card (on either interface) is 127.0.0.1. I can change that to a valid IP address on my... (8 Replies)
Discussion started by: Ask Me
8 Replies
boot(1M) boot(1M)
NAME
boot - bootstrap process
DESCRIPTION
Itanium-based System Hardware
An system's bootstrap process involves the execution of four software components:
o CMOS
o option ROM
o EFI
o Boot Manager
o (see hpux.efi(1M)).
After the processor is reset, firmware initializes and tests processors and platform. During initialization, the firmware lets a user
interrupt and configure CMOS and option ROMs. It then transfers control to EFI, the Extensible Firmware Interface. EFI, in turn, initial-
izes EFI boot and runtime services and launches the Boot Manager. The Boot Manager, which allows loading of EFI application or drivers
from EFI defined file system, loads and transfers control to the HP-UX-specific bootstrap loader. then loads the HP-UX kernel object file
from the HP-UX file system to memory and transfers control to the loaded kernel image.
PA-RISC Hardware
The PA-RSIC bootstrap process involves the execution of three software components:
o (see pdc(1M),
o (see isl(1M), and
o (see hpux(1M).
After the processor is RESET, the (firmware), performs a self-test and initializes the processor. It then loads and transfers control to
the operating-system-independent in turn, loads and transfers control to the utility, the HP-UX-specific bootstrap loader. then downloads
the HP-UX kernel object file from an HP-UX file system and transfers control to the loaded kernel image.
SEE ALSO
hpux(1M), hpux.efi(1M), isl(1M), pdc(1M), efi(4).
boot(1M)
