10 More Discussions You Might Find Interesting
1. HP-UX
I own a 1999 vintage HP Logic Analyzer that runs HPUX 10.20. It is a 9000/775/rock system similar to a Visualize C132L/160L system.
I'm attempting, mostly for the fun of it, to upgrade the existing slow 5MB/s-only SCSI system, with a new-er PCI card. Of course drivers is my major concern. I'd... (2 Replies)
Discussion started by: KeithM
2 Replies
2. SCO
OK group, it's been 12 years since I worked with SCO. I need some direction here:
SCO Openserver 5.07
I have a server with a bad motherboard. I have moved the SCSI adapter and hard drive to another computer. This new server has different hardware so I must install the chipset drivers for... (1 Reply)
Discussion started by: jscholz
1 Replies
3. SCO
PCI-X was popular years ago, now it's not. Today's motherboards have PCIe slots, not PCI-X slots. I'm accustomed to using Adaptec, but I believe they've been bought out by ATTO Technology. Now ATTO has a product called PCI UL50 Dual Channel VHDCI Ultra320 SCSI PCIe card. So: does the SCO UNIX... (7 Replies)
Discussion started by: Transpower
7 Replies
4. AIX
All
I am at a loss with a VIO server running ios 2.2.0.10-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable:
$ lsnports
name physloc ... (4 Replies)
Discussion started by: johnf
4 Replies
5. Hardware
I need to connect 80pin SCA Ultra320 SCSI hdd to 68pin.
There are rumors that some bad "passive" adapters with problematic termination can fry the HDD. The adapter we got is Assmann ABSCA-2. Hard drive is 'Fujitsu MAW3073NC'
Do we need to set any jumpers before turning it on?
We already had... (0 Replies)
Discussion started by: orange47
0 Replies
6. SCO
I'm floundering here trying to locate a PCI-E 1x HBA that will support an external tape drive in SCO Openserver 6. I was unable to find anything that would work in the compatible hardware list and a call to Adaptec confirmed that PCI-X would've been a better option for the risers in the Dell 2950... (1 Reply)
Discussion started by: s_mal
1 Replies
7. AIX
I have 1 PCI-X Dual Channel Ultra320 SCSI Adapter card for my p570 server. I would like to split the 2 channels for the usage of 2 tape drives in different LPARs. Is that possible?
For example, I have 2 LPARs running in p570 server, LPAR-A configured the Ultra320 card as pci7 in slot... (11 Replies)
Discussion started by: kwliew999
11 Replies
8. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
9. Solaris
Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy.
I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this... (4 Replies)
Discussion started by: Plain Person
4 Replies
10. UNIX for Dummies Questions & Answers
Can anyone out there help me out? I'm trying to install a scsi tape back up on a sys running sco openserver 5.0.4. When I go through the steps for mkdev tape it seems like it works, but when I reboot I still don't see the tape. Also when it boots up I get a scsi bios not installed error. I've... (1 Reply)
Discussion started by: goatboy_tx
1 Replies
IPRINIT(8) System Manager's Manual IPRINIT(8)
NAME
iprinit - IBM Power RAID adapter/device initialization utility
SYNOPSIS
iprinit
iprinit --debug --daemon --use-polling --use-uevents
DESCRIPTION
iprinit is used to setup IBM Power RAID adapters and devices for optimal performance. It will enable U320 scsi speeds if it is determined
the disk enclosure supports it. It will also enable tagged command queuing. Any scsi bus attributes, such as bus width, or disk
attributes, such as queue depth, that have been setup by iprconfig will be loaded as well. It is desired that this be called in the boot
process, using the init.d script provided.
OPTIONS
--version
Print the version number of iprinit
--debug
Enable additional error logging. Enabling this will result in additional errors logging to /var/log/messages.
--daemon
Run as a daemon to handle adapters and devices being hotplugged.
--use-polling
Do not use netlink/uevent notification, but rather poll for adapter and device configuration changes.
--use-uevents
Use netlink/uevent notification rather than polling for adapter and device configuration changes. If not specified, polling will be
used until the first uevent notification appears, then netlink will be used.
AUTHOR
Brian King (brking@us.ibm.com)
February 2005 IPRINIT(8)