configuring nic card

9 More Discussions You Might Find Interesting

1. UNIX for Beginners Questions & Answers

Configuring NIC device in Solaris 9 SPARC OS [QEMU]

I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only. ...

2. HP-UX

NIC card issue

Hi, Someone asked me the below. If the box has multiple NIC cards, try to run a test with interface address specified as shown below $ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress> How can I now find out if my box has multiple NIC cards and how can I...

3. Solaris

NIC card repetative Failover

I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2 When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously. Following are the message log. ifmsdb1 in.mpathd: NIC failure detected...

4. Solaris

Reg. NIC card

Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than...

5. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks

6. IP Networking

Problem configuring NIC in DGUX

Old DG box Aviion PentiumPro running R4.20Mu06 being used to try to recreate Ingres db from backup tapes so machine has not been operational before and some of original files in /etc may have ben overwritten Unable to get NIC working Any pointers on how to go about configuring NIC :rolleyes:

7. Solaris

Configuring 1 Nic card with 2 IP addresses and 2 seperate default Gateways in Solaris

Hi ...... I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways. ( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip) Thanks, Remi

8. HP-UX

Configuring NIC

Hi. I have HP-9000 Server running HP-UX 10.20. rECENTLY OUR network upgraded to 100mb/sec and I want to do same on the server. So, I add the second Network card (100MB). But the problem is, I can't find a way of configuring this card. How am i going to tell the server to use this 100mb card...

9. UNIX for Advanced & Expert Users

No NIC Card?

Hello Everyone, While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use. There is no output for dmesg|grep eth. Does that mean that mandrake...

LEARN ABOUT CENTOS

ocf_heartbeat_sendarp

OCF_HEARTBEAT_SENDAR(7) 					OCF resource agents					   OCF_HEARTBEAT_SENDAR(7)

NAME

       ocf_heartbeat_SendArp - Broadcasts unsolicited ARP announcements

SYNOPSIS

       SendArp [start | stop | monitor | meta-data | validate-all]

DESCRIPTION

       This RA can be used _instead_ of the IPaddr2 or IPaddr RA to send gratuitous ARP for an IP address on a given interface, without adding the
       address to that interface. For example, if for some resaon you wanted to send gratuitous ARP for addresses managed by IPaddr2 or IPaddr on
       an additional interface.

SUPPORTED PARAMETERS

       ip
	   The IP address for sending ARP packet.

	   (required, string, no default)

       nic
	   The NIC for sending ARP packet.

	   (required, string, no default)

       background
	   Send ARPs in background. Set to false if you want to test if sending ARPs succeeded.

	   (optional, boolean, default true)

SUPPORTED ACTIONS

       This resource agent supports the following actions (operations):

       start
	   Starts the resource. Suggested minimum timeout: 20s.

       stop
	   Stops the resource. Suggested minimum timeout: 20s.

       monitor
	   Performs a detailed status check. Suggested minimum timeout: 20. Suggested interval: 10.

       meta-data
	   Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5.

       validate-all
	   Performs a validation of the resource configuration. Suggested minimum timeout: 20s.

EXAMPLE

       The following is an example configuration for a SendArp resource using the crm(8) shell:

	   primitive p_SendArp ocf:heartbeat:SendArp 
	     params 
	       ip=string 
	       nic=string 
	     op monitor depth="0" timeout="20" interval="10"

SEE ALSO

       http://www.linux-ha.org/wiki/SendArp_(resource_agent)

AUTHOR

       Linux-HA contributors (see the resource agent source for information about individual authors)

resource-agents UNKNOWN 					    06/09/2014						   OCF_HEARTBEAT_SENDAR(7)

HP-UX