configuring nic card

9 More Discussions You Might Find Interesting

1. UNIX for Beginners Questions & Answers

Configuring NIC device in Solaris 9 SPARC OS [QEMU]

I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only. ...

2. HP-UX

NIC card issue

Hi, Someone asked me the below. If the box has multiple NIC cards, try to run a test with interface address specified as shown below $ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress> How can I now find out if my box has multiple NIC cards and how can I...

3. Solaris

NIC card repetative Failover

I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2 When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously. Following are the message log. ifmsdb1 in.mpathd: NIC failure detected...

4. Solaris

Reg. NIC card

Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than...

5. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks

6. IP Networking

Problem configuring NIC in DGUX

Old DG box Aviion PentiumPro running R4.20Mu06 being used to try to recreate Ingres db from backup tapes so machine has not been operational before and some of original files in /etc may have ben overwritten Unable to get NIC working Any pointers on how to go about configuring NIC :rolleyes:

7. Solaris

Configuring 1 Nic card with 2 IP addresses and 2 seperate default Gateways in Solaris

Hi ...... I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways. ( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip) Thanks, Remi

8. HP-UX

Configuring NIC

Hi. I have HP-9000 Server running HP-UX 10.20. rECENTLY OUR network upgraded to 100mb/sec and I want to do same on the server. So, I add the second Network card (100MB). But the problem is, I can't find a way of configuring this card. How am i going to tell the server to use this 100mb card...

9. UNIX for Advanced & Expert Users

No NIC Card?

Hello Everyone, While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use. There is no output for dmesg|grep eth. Does that mean that mandrake...

LEARN ABOUT SUSE

ocf_heartbeat_aoetarget

OCF_HEARTBEAT_AOETAR(7) 					OCF resource agents					   OCF_HEARTBEAT_AOETAR(7)

NAME

       ocf_heartbeat_AoEtarget - Manages ATA-over-Ethernet (AoE) target exports

SYNOPSIS

       AoEtarget [start | stop | monitor | reload | meta-data | validate-all]

DESCRIPTION

       This resource agent manages an ATA-over-Ethernet (AoE) target using vblade. It exports any block device, or file, as an AoE target using
       the specified Ethernet device, shelf, and slot number.

SUPPORTED PARAMETERS

       device
	   The local block device (or file) to export as an AoE target. (required, string, no default)

       nic
	   The local Ethernet interface to use for exporting this AoE target. (required, string, default eth0)

       shelf
	   The AoE shelf number to use when exporting this target. (optional, integer, no default)

       slot
	   The AoE slot number to use when exporting this target. (required, integer, no default)

       pid
	   The file to record the daemon pid to. (optional, string, default /var/run/resource-agents/AoEtarget-default.pid)

       binary
	   Location of the vblade binary. (optional, string, default /usr/sbin/vblade)

SUPPORTED ACTIONS

       This resource agent supports the following actions (operations):

       start
	   Starts the resource. Suggested minimum timeout: 15.

       stop
	   Stops the resource. Suggested minimum timeout: 15.

       monitor
	   Performs a detailed status check. Suggested minimum timeout: 15. Suggested interval: 10.

       reload
	   Suggested minimum timeout: 15.

       meta-data
	   Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5.

       validate-all
	   Performs a validation of the resource configuration. Suggested minimum timeout: 15.

EXAMPLE

       The following is an example configuration for a AoEtarget resource using the crm(8) shell:

	   primitive example_AoEtarget ocf:heartbeat:AoEtarget 
	     params 
	       device=string 
	       nic="eth0" 
	       slot=integer 
	     op monitor timeout="15" interval="10" depth="0"

SEE ALSO

       http://www.linux-ha.org/wiki/AoEtarget_(resource_agent)

AUTHOR

       Linux-HA contributors (see the resource agent source for information about individual authors)

resource-agents 1.0.3						    07/05/2010						   OCF_HEARTBEAT_AOETAR(7)

HP-UX