9 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
2. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
3. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
4. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
5. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
6. IP Networking
Old DG box Aviion PentiumPro running R4.20Mu06 being used to try to recreate Ingres db from backup tapes so machine has not been operational before and some of original files in /etc may have ben overwritten
Unable to get NIC working
Any pointers on how to go about configuring NIC :rolleyes: (0 Replies)
Discussion started by: lindab
0 Replies
7. Solaris
Hi ......
I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways.
( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip)
Thanks,
Remi (1 Reply)
Discussion started by: Remi
1 Replies
8. HP-UX
Hi.
I have HP-9000 Server running HP-UX 10.20. rECENTLY OUR network upgraded to 100mb/sec and I want to do same on the server. So, I add the second Network card (100MB). But the problem is, I can't find a way of configuring this card. How am i going to tell the server to use this 100mb card... (1 Reply)
Discussion started by: wobitu
1 Replies
9. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
nsquery(1) General Commands Manual nsquery(1)
Name
nsquery - name server query command
Syntax
/usr/ucb/nsquery [ lookup ] [ host ] [ server ]
Description
The command provides an interface to obtain host name and address information.
If you specify host, the command obtains information about the specified host. If no host is specified, the command obtains information
about the local host system.
If you specify server, the command queries the BIND server that you specify. If you do not specify a server, the command queries the
default BIND server.
Options
lookup Retrieves the host name, Internet Protocol (IP) address, and aliases of the specified host. If no host or server is specified, the
command obtains information about the local system from the default BIND server.
If you do specify the lookup option, the command obtains the information about the BIND server and host specified (or their
defaults). If the system from which you issue the command is a BIND server, and you do not specify the lookup option, information
about only that server is retrieved.
Files
Directory containing BIND server data file
BIND server boot file
Host database file containing name to address mapping for BIND primary
server
Host database file containing address to name mapping for BIND primary
server
Local host database file containing address to name mapping for BIND
server
BIND server cache file
BIND data file
See Also
nslookup(1), resolver(3), resolver(5), named(8)
Guide to the BIND/Hesiod Service
nsquery(1)
