9 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
2. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
3. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
4. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
5. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
6. IP Networking
Old DG box Aviion PentiumPro running R4.20Mu06 being used to try to recreate Ingres db from backup tapes so machine has not been operational before and some of original files in /etc may have ben overwritten
Unable to get NIC working
Any pointers on how to go about configuring NIC :rolleyes: (0 Replies)
Discussion started by: lindab
0 Replies
7. Solaris
Hi ......
I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways.
( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip)
Thanks,
Remi (1 Reply)
Discussion started by: Remi
1 Replies
8. HP-UX
Hi.
I have HP-9000 Server running HP-UX 10.20. rECENTLY OUR network upgraded to 100mb/sec and I want to do same on the server. So, I add the second Network card (100MB). But the problem is, I can't find a way of configuring this card. How am i going to tell the server to use this 100mb card... (1 Reply)
Discussion started by: wobitu
1 Replies
9. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
cachefslog(1M) System Administration Commands cachefslog(1M)
NAME
cachefslog - Cache File System logging
SYNOPSIS
cachefslog [-f logfile | -h] cachefs_mount_point
DESCRIPTION
The cachefslog command displays where CacheFS statistics are being logged. Optionally, it sets where CacheFS statistics are being logged,
or it halts logging for a cache specified by cachefs_mount_point. The cachefs_mount_point argument is a mount point of a cache file system.
All file systems cached under the same cache as cachefs_mount_point will be logged.
OPTIONS
The following options are supported. You must be super-user to use the -f and -h options.
-f logfile Specify the log file to be used.
-h Halt logging.
OPERANDS
cachefs_mount_point A mount point of a cache file system.
USAGE
See largefile(5) for the description of the behavior of cachefslog when encountering files greater than or equal to 2 Gbyte ( 2**31 bytes).
EXAMPLES
Example 1: Checking the Logging of a directory.
The example below checks if the directory /home/sam is being logged:
example% cachefslog /home/sam
not logged: /home/sam
Example 2: Changing the logfile.
The example below changes the logfile of /home/sam to /var/tmp/samlog:
example# cachefslog -f /var/tmp/samlog /home/sam
/var/tmp/samlog: /home/sam
Example 3: Verifying the change of a logfile.
The example below verifies the change of the previous example:
example% cachefslog /home/sam
/var/tmp/samlog: /home/sam
Example 4: Halting the logging of a directory.
The example below halts logging for the /home/sam directory:
example# cachefslog -h /home/sam
not logged: /home/sam
EXIT STATUS
The following exit values are returned:
0 success
non-zero an error has occurred.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
cachefsstat(1M), cachefswssize(1M), cfsadmin(1M), attributes(5), largefile(5)
DIAGNOSTICS
Invalid path It is illegal to specify a path within a cache file system.
SunOS 5.10 7 Feb 1997 cachefslog(1M)