HP�s ProLiant DL120 G5 SATA Rack Server

3 More Discussions You Might Find Interesting

1. Hardware

Connect SATA Laptop HardDrive to Desktop SATA Slots

Hello everybody, I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors. The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my...

2. UNIX for Advanced & Expert Users

trying to setup a sata drive using a sata to scsi adaptor

trying to setup a sata drive using a sata to scsi adaptor I have a sata 1TB Deskstar that I had setup before and during shipment from a facilty to another, the disk failed. The handling was not great, lots of throwing boxes, etc. I have a new disk from Hitachi (thankyou Hitachi) anyway, I don't...

3. Red Hat

Installation problem in HP Proliant DL-380 G5 server

Dear Sir, I have one HP Proliant DL-380 G5 Server, i tried to install Redhat Enterprise Verison 4, when i am trying to install the linux operating system it is coming one error message your hard disk not found, we are using Serial Scsi harddisk 146 GB, array controller is p400. i would...

LEARN ABOUT NETBSD

arcmsr

ARCMSR(4)						   BSD Kernel Interfaces Manual 						 ARCMSR(4)

NAME

     arcmsr -- Areca Technology Corporation SATA/SAS RAID controller

SYNOPSIS

     arcmsr* at pci? dev ? function ?

DESCRIPTION

     The arcmsr driver provides support for the PCI-X and PCI Express RAID controllers from Areca Technology Corporation:

	   -   ARC-1110 PCI-X 4 Port SATA RAID Controller
	   -   ARC-1110ML PCI-X 4 Port SATA RAID Controller
	   -   ARC-1120 PCI-X 8 Port SATA RAID Controller
	   -   ARC-1120ML PCI-X 8 Port SATA RAID Controller
	   -   ARC-1130 PCI-X 12 Port SATA RAID Controller
	   -   ARC-1130ML PCI-X 12 Port SATA RAID Controller
	   -   ARC-1160 PCI-X 16 Port SATA RAID Controller
	   -   ARC-1160ML PCI-X 16 Port SATA RAID Controller
	   -   ARC-1170 PCI-X 24 Port SATA RAID Controller
	   -   ARC-1200 Rev A PCI Express 2 Port SATA RAID Controller
	   -   ARC-1202 PCI Express 2 Port SATA RAID Controller
	   -   ARC-1210 PCI Express 4 Port SATA RAID Controller
	   -   ARC-1220 PCI Express 8 Port SATA RAID Controller
	   -   ARC-1230 PCI Express 12 Port SATA RAID Controller
	   -   ARC-1230ML PCI Express 12 Port SATA RAID Controller
	   -   ARC-1231ML PCI Express 12 Port SATA RAID Controller
	   -   ARC-1260 PCI Express 16 Port SATA RAID Controller
	   -   ARC-1260ML PCI Express 16 Port SATA RAID Controller
	   -   ARC-1261ML PCI Express 16 Port SATA RAID Controller
	   -   ARC-1280 PCI Express 24 Port SATA RAID Controller
	   -   ARC-1280ML PCI Express 24 Port SATA RAID Controller
	   -   ARC-1680 PCI Express 8 Port SAS RAID Controller
	   -   ARC-1680LP PCI Express 8 Port SAS RAID Controller
	   -   ARC-1680i PCI Express 8 Port SAS RAID Controller
	   -   ARC-1680x PCI Express 8 Port SAS RAID Controller
	   -   ARC-1681 PCI-X 8 Port SAS RAID Controller

     These controllers support RAID levels 0, 1, 1E, 3, 5, 6, and JBOD using either SAS or SATA II drives.

     arcmsr supports management and monitoring of the controller through the bioctl(8) and envstat(8) commands.

     Please note, however, that to use some features that require special privileges, such as creating/removing hot-spares, pass-through disks or
     RAID volumes will require to have the password disabled in the firmware; otherwise a Permission denied error will be reported by bioctl(8).

     When a RAID 1 or 1+0 volume is created, either through the bioctl(8) command or controller's firmware, the volume won't be accessible until
     the initialization is done.  A way to get access to the sd(4) device that corresponds to that volume without rebooting, is to issue the fol-
     lowing command (once the initialization is finished):

     $ scsictl scsibus0 scan any any

     The arcmsr driver will also report to the kernel log buffer any error that might appear when handling firmware commands, such as used by the
     bioctl(8) command.

EVENTS

     The arcmsr driver is able to send events to powerd(8) if a volume or any drive connected to the volume is not online.  The state-changed
     event will be sent to the /etc/powerd/scripts/sensor_drive script when such condition happens.

SEE ALSO

     intro(4), pci(4), scsi(4), sd(4), bioctl(8), envstat(8), powerd(8), scsictl(8)

HISTORY

     The arcmsr driver first appeared in NetBSD 5.0.

AUTHORS

     The arcmsr driver was originally written for OpenBSD by David Gwynne.  It was ported to NetBSD and extended by Juan Romero Pardines.

BSD
								   March 3, 2008							       BSD

HP Server News and Podcasts RSS