on an m5000 , I can not power it up, system failure.
Code:
XSCF> poweron -a
DomainIDs to power on:00,01
Continue? [y|n] :y
00 :Not powering on :Poweron canceled due to missing component.
01 :Not powering on :Poweron canceled due to missing component.
XSCF> showboards -a
XSB DID(LSB) Assignment Pwr Conn Conf Test Fault
---- -------- ----------- ---- ---- ---- ------- --------
00-0 00(00) Assigned n n n Passed Faulted
00-1 01(04) Assigned n n n Passed Faulted
00-2 01(05) Assigned n n n Passed Faulted
00-3 01(06) Assigned n n n Passed Faulted
01-0 01(00) Assigned n n n Passed Faulted
01-1 01(01) Assigned n n n Passed Faulted
01-2 01(02) Assigned n n n Passed Faulted
01-3 01(03) Assigned n n n Passed Faulted
do I need a new motherboard, or just the one piece that faulted?
Last edited by rbatte1; 06-19-2018 at 08:58 AM..
Reason: Added CODE tags for all output for clarity (and disabling the smilies)
Do you have support for the M5000? I would say replacing the faulted part should be enough. You can also try to reset the fault and try again to powerup the system. But go slowly with a poweron -d 0 first and see what happens. If domain 0 is running, you can try to start domain 1.
no support since its older. just a company that swaps parts. I did try the power on each domain and same result , did no reset fault, what command does that? I will try and find it.
Sun shipped some mobo's in COD (Capacity on Demand) mode which means they won't work without a license. Have you got one of those? Do you know the machine history?
no support since its older. just a company that swaps parts. I did try the power on each domain and same result , did no reset fault, what command does that? I will try and find it.
From the XSCF use the command version -c xcp and send the output. Depending on the version you might not be able to reset the error...
Can anyone offer any advice on how to modify the script below to work on a new system we have, that has no graphics capability? We admin the system through a serial RAS device. I've tried running the below script through the RAS and through an ssh -X session. It failed with something like "GTK... (3 Replies)
A team member installed the wrong version of License Code on a Power 740 system used in our Development environment.
The system will no longer boot.
Does anyone have IBM documentation or experience to share on recovering a system that currently reports "Unsupported License Code version... (1 Reply)
I have an m5000 that Is down.
I have access to XSCF>
and was able to get to the ok prompt.
However, on
>ok boot
it failed to boot.
erred with :
svc.startd: svc:/system/device/fc-fabric:default: Method "/lib/svc/method/fc-fabric" failed due to signal KILL.
Nov 29... (3 Replies)
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
I have an M5K with disk issues I'm trying to troubleshoot, and it's causing me some confusion. I know the host has four on-board HDDs, but the format command's output shows c0t0d0, c0t1d0, c3t0d0, and c3t1d0. cfgadm -al shows c0t3d0 as the DVD-ROM drive, and c1 and c2 as SAN disks. Confused yet?
... (2 Replies)
Hi i 've a M5000 running 2 domains in my Lab with following hardconf
SPARC Enterprise M5000; Memory_Size:128 GB;
+-----------------------------------+------------+
| FRU | Quantity |
+-----------------------------------+------------+
| MBU_B... (3 Replies)
Hi,
I 've a fully loaded M5000 which i would like to partition in 4 domains but i have a concern that since we have only 4 internal disks how can we partition the box in for domains with 2 disks ( mirrored ) in each domain. Should i go ahead with 1 Lun from SAN and 1 internal disk for each of 4... (3 Replies)
Hello:
NOOB here. I attempted to use smit mkcd. Failed on first attempt, not enough space. 2nd attempt tried to place iso on /usr, not enough space there. Cleanup ran for about 5 minutes after aborting. Now AIX won't boot. LCD display on 7029-6E3 says: 0517 MOUNT /USR. Attempted to boot from CD... (11 Replies)
06-19-2018
