8 More Discussions You Might Find Interesting
1. Hardware
Hi All,
I am having an Sun fire X4600 M2 server where one of the interfaces is down.
I had requested for the replacement but had a bit problem in identifying the port.
As per the server service module, there are 4 NIC ports and one port is not flashing (e1000g0) but as per server, the port... (8 Replies)
Discussion started by: Rockyc3400
8 Replies
2. Solaris
Hi Folks,
Has anyone seen these errors on bootup.
Mar 15 12:22:30 svc.startd: svc:/system/device/local:default: Method "/lib/svc/method/devices-local" failed due to signal SEGV.ht (c) 1983, 2010,
Oracle and/or its affiliates. All rights reserved.
Configuring devices. ... (1 Reply)
Discussion started by: ESSTEAM
1 Replies
3. Solaris
Hi,
I perform clrs enable/disable resource-group to start/shutown sybase db.
If I do it through through scsetup , it asks for Do you require to change the state of resource "sybaseapp-rs" on individual nodes or zones that can master the resource (yes/no) ?.
I am bit confused of above... (1 Reply)
Discussion started by: tuxian
1 Replies
4. Solaris
One of my X4600 server had a power loss and rebooted and now its giving me a strange problem servers internal disk controller naming has changed by itself ... the after failsafe boot md.conf file shows following c3txdx but shows internal disk at c4txdx ... what could be the reason for this and... (1 Reply)
Discussion started by: fugitive
1 Replies
5. Solaris
I need to configure the iLOM for x4600 server. before I can set the IP details and commit, I need to set network state should be enabled. However my firmware is already the latest and I need not upgrade. I am not able to set the /SP/network state to enable. pls assist. i BELIEVE the bug was fixed... (5 Replies)
Discussion started by: incredible
5 Replies
6. Solaris
Hi,
I ;ve a SUN x4600 running solaris 10. I want to connect to the system remotely form console like we can connect to sparc sc or alom .. (9 Replies)
Discussion started by: fugitive
9 Replies
7. Linux
Anyone have tips on configuring the 2.6.10 kernel to take full advantage of dual 2.4 Ghz Xeons?
I'm not getting expected benchmark results.... and seemingly was better off with a single 2600+ AMD processor. (1 Reply)
Discussion started by: Neo
1 Replies
8. Solaris
I've upgraded Iplannet 4.1 to Sun ONE Web Server 6.1. However. Now i can't seem to connect on port 4443 which was originally being used in 4.1 to deal with transactions....when i try to run a query on this port (4443) i get the following error:
Access to the server was denied
I suspect i... (1 Reply)
Discussion started by: AJD
1 Replies
SIBA(4) BSD Kernel Interfaces Manual SIBA(4)
NAME
siba -- Sonic Inc. Silicon Backplane driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device siba
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
siba_load="YES"
DESCRIPTION
The siba driver supports the Sonic Inc. Silicon Backplane, the interblock communications architecture that can be found in most Broadcom
wireless NICs.
A bus connects all of the Silicon Backplane's functional blocks. These functional blocks, known as cores, use the Open Core Protocol (OCP)
interface to communicate with agents attached to the Silicon Backplane.
Each NIC uses a chip from the same chip family. Each member of the family contains a different set of cores, but shares basic architectural
features such as address space definition, interrupt and error architecture, and backplane register definitions.
Each core can have an initiator agent that passes read and write requests onto the system backplane and a target agent that returns responses
to those requests. Not all cores contain both an initiator and a target agent. Initiator agents are present in cores that contain host
interfaces (PCI, PCMCIA), embedded processors (MIPS), or DMA processors associated with communications cores.
All cores other than PCMCIA have a target agent.
SEE ALSO
bwn(4)
HISTORY
The siba device driver first appeared in FreeBSD 8.0.
AUTHORS
The siba driver was written by Bruce M. Simpson <bms@FreeBSD.org> and Weongyo Jeong <weongyo@FreeBSD.org>.
CAVEATS
Host mode is not supported at this moment.
BSD
January 8, 2010 BSD
