currently I am doing some inventory on our hardware.
I know that the old school IBM 3583 tape drive has some license
feature enable but I dont know where can I check If the feature
currently enable or not on our drive...
Ive checked trough Web Base and Panel base but nowhere I can found
Model : UTL358302 ( IBM ULT3583-TL )
Drive Firmware 73P5
Library Firmware 6.10.0004
On our TS3310 tape Drive , It is very easy to check. as it is included on Web Base Information list
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Hi ,
We have a Blade Chassis H housing 4 servers. It has a single tape drive. Can i share this tape drive with a HP Server Running Windows Server 2003? They are in the same LAN btw. (0 Replies)
Hello every body, I have one tape library 3583 but I can't install this some body have ben installed??
when I tray to install it, the output is the next:
Method error (/etc/methods/cfgAtape):
0514-022 The specified connection is not valid.
some Idea??
thanks
greetings (5 Replies)
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
BACKUP_STATUS(8) AFS Command Reference BACKUP_STATUS(8)NAME
backup_status - Reports a Tape Coordinator's status
SYNOPSIS
backup status [-portoffset <TC port offset>]
[-localauth] [-cell <cell name>] [-help]
backup st [-p <TC port offset>]
[-l] [-c <cell name>] [-h]
DESCRIPTION
The backup status command displays which operation, if any, the indicated Tape Coordinator is currently executing.
OPTIONS -portoffset <TC port offset>
Specifies the port offset number of the Tape Coordinator for which to report the status.
-localauth
Constructs a server ticket using a key from the local /etc/openafs/server/KeyFile file. The backup command interpreter presents it to
the Backup Server, Volume Server and VL Server during mutual authentication. Do not combine this flag with the -cell argument. For more
details, see backup(8).
-cell <cell name>
Names the cell in which to run the command. Do not combine this argument with the -localauth flag. For more details, see backup(8).
-help
Prints the online help for this command. All other valid options are ignored.
OUTPUT
The following message indicates that the Tape Coordinator is not currently performing an operation:
Tape coordinator is idle
Otherwise, the output includes a message of the following format for each running or pending operation:
Task <task_ID>: <operation>: <status>
where
<task_ID>
Is a task identification number assigned by the Tape Coordinator. It begins with the Tape Coordinator's port offset number.
<operation>
Identifies the operation the Tape Coordinator is performing, which is initiated by the indicated command:
Dump
The backup dump command.
Restore
The backup diskrestore, backup volrestore, or backup volsetrestore commands.
Labeltape
The backup labeltape command.
Scantape
The backup scantape command.
SaveDb
The backup savedb command.
RestoreDb
The backup restoredb command.
<status>
Indicates the job's current status in one of the following messages.
number Kbytes transferred, volume volume_name
For a running dump operation, indicates the number of kilobytes copied to tape or a backup data file so far, and the volume
currently being dumped.
number Kbytes, restore.volume
For a running restore operation, indicates the number of kilobytes copied into AFS from a tape or a backup data file so far.
[abort requested]
The backup kill command was issued, but the termination signal has yet to reach the Tape Coordinator.
[abort sent]
The operation is canceled by the backup kill command. Once the Backup System removes an operation from the queue or stops it from
running, it no longer appears at all in the output from the command.
[butc contact lost]
The backup command interpreter cannot reach the Tape Coordinator. The message can mean either that the Tape Coordinator handling
the operation was terminated or failed while the operation was running, or that the connection to the Tape Coordinator timed out.
[done]
The Tape Coordinator has finished the operation.
[drive wait]
The operation is waiting for the specified tape drive to become free.
[operator wait]
The Tape Coordinator is waiting for the backup operator to insert a tape in the drive.
If the Tape Coordinator is communicating with an XBSA server (a third-party backup utility that implements the Open Group's Backup Service
API [XBSA]), the following message appears last in the output:
<XBSA_program> Tape coordinator
where <XBSA_program> is the name of the XBSA-compliant program.
EXAMPLES
The following example shows that the Tape Coordinator with port offset 4 has so far dumped about 1.5 MB of data for the current dump
operation, and is currently dumping the volume named "user.pat.backup":
% backup status -portoffset 4
Task 4001: Dump: 1520 Kbytes transferred, volume user.pat.backup
PRIVILEGE REQUIRED
The issuer must be listed in the /etc/openafs/server/UserList file on every machine where the Backup Server is running, or must be logged
onto a server machine as the local superuser "root" if the -localauth flag is included.
SEE ALSO backup(8), butc(8)COPYRIGHT
IBM Corporation 2000. <http://www.ibm.com/> All Rights Reserved.
This documentation is covered by the IBM Public License Version 1.0. It was converted from HTML to POD by software written by Chas
Williams and Russ Allbery, based on work by Alf Wachsmann and Elizabeth Cassell.
OpenAFS 2012-03-26 BACKUP_STATUS(8)