10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello All,
I have Linux box with two interface cards.
Every card has it's own IP Address and Gateway, IP addresses are from different subnets.
eth0 192.168.1.10/24 GW 192.168.1.1
eth1 192.168.2.10/24 GW 192.168.2.1
Third PC is located in 192.168.13.0/24 network and is trying to access... (2 Replies)
Discussion started by: AndreiM
2 Replies
2. IP Networking
Hi all,
Host - Ubuntu 12.04 desktop 64bit
Virtualizer - Oracle VirtualBox
2 NICs
Where can I find relevant document to set up 2 NICs, one for inward bound and another for outward bound, separate channel, both connected to the same router
Would following document be appropriate for my... (1 Reply)
Discussion started by: satimis
1 Replies
3. Red Hat
Hi,
I have to get into BIOS and disable onbaord NICS for an IBM server, can someone please help me out.
I tried hitting F1 when reboot to get into BIOS, but it seems like a setup screen and I dont see any option to disable NICS?
Thanks
Sam (0 Replies)
Discussion started by: sam4919
0 Replies
4. Red Hat
Hi all Expertise,
I have following issue to solve,
SSL / TLS Renegotiation DoS (low) 222.225.12.13
Ease of Exploitation Moderate
Port 443/tcp
Family Miscellaneous
Following is the problem description:------------------
Description The remote service encrypts traffic using TLS / SSL and... (2 Replies)
Discussion started by: manalisharmabe
2 Replies
5. Shell Programming and Scripting
Hi All,
I have bash script, so what is sintax script in bash for Enable and Disable Tab Key. Thanks for your help.:(
Thanks,
Rico (1 Reply)
Discussion started by: carnegiex
1 Replies
6. UNIX for Dummies Questions & Answers
Hi;
Is there a way to determine for sure how many NIC ports installed on my Linux box?
I tried to run "lspci" but not sure about the results, it's not clear.
Below are the results when i run both "ifconfig" & "lspci" on my Linux box i hope someone can help me finding the actual numbers of... (1 Reply)
Discussion started by: Katkota
1 Replies
7. Linux
I'm looking for a way in RHL 5.1 to use two NICs on one host with two physical IP addresses and map them under one virtual IP address, i.e. NIC 1 10.10.10.1 NIC2 10.10.10.2 VIP 192.168.10.1
Basically I want either one of the NICs to ARP for the VIP. No load balancing required just HA. (2 Replies)
Discussion started by: wschmied
2 Replies
8. Solaris
Hi, is there a way in Solaris 8 to determine how many total NIC's say a Sun Sparc box has installed - plumbed or unplumbed - and find out its capable network speeds and MAC address?
I know ifconfig -a but that only shows the plumbed and used interfaces.
thx
cc (2 Replies)
Discussion started by: bigapple100
2 Replies
9. IP Networking
FreeBSD 4.8, Apache 1.3.27 - two NICs, one with a real-world IP plugged into a switch outside the PIX firewall, the other with a private IP plugged into a switch inside the PIX firewall. Apache listens on both IPs. my domain is mydomain.org.
so in /etc/rc.conf i have something like this (these... (10 Replies)
Discussion started by: ednix
10 Replies
10. AIX
Hi friends,
I installed oracle 10g (10.2.0.2) RAC on 2 IBM p5 570 servers running AIX 5.3ML04 and HACMP5.2 (used Raw devices, not used GPFS). Each server has 4 x 1Gbps ethernet cards (NICs), en0 and en1 for boot address, en2 and en3 for oracle interconnect.
Now i want to merge 2 NICs (en2 and... (1 Reply)
Discussion started by: bong02
1 Replies