12-04-2011
Hi, about the model I think it is 7945P, 3635X
By hitting F1 I was able to get into setup screen and I am not sure this is where I should go to disable NICS?
Thank you
Sam
10 More Discussions You Might Find Interesting
1. AIX
Hi friends,
I installed oracle 10g (10.2.0.2) RAC on 2 IBM p5 570 servers running AIX 5.3ML04 and HACMP5.2 (used Raw devices, not used GPFS). Each server has 4 x 1Gbps ethernet cards (NICs), en0 and en1 for boot address, en2 and en3 for oracle interconnect.
Now i want to merge 2 NICs (en2 and... (1 Reply)
Discussion started by: bong02
1 Replies
2. IP Networking
FreeBSD 4.8, Apache 1.3.27 - two NICs, one with a real-world IP plugged into a switch outside the PIX firewall, the other with a private IP plugged into a switch inside the PIX firewall. Apache listens on both IPs. my domain is mydomain.org.
so in /etc/rc.conf i have something like this (these... (10 Replies)
Discussion started by: ednix
10 Replies
3. Solaris
Hi, is there a way in Solaris 8 to determine how many total NIC's say a Sun Sparc box has installed - plumbed or unplumbed - and find out its capable network speeds and MAC address?
I know ifconfig -a but that only shows the plumbed and used interfaces.
thx
cc (2 Replies)
Discussion started by: bigapple100
2 Replies
4. Linux
I'm looking for a way in RHL 5.1 to use two NICs on one host with two physical IP addresses and map them under one virtual IP address, i.e. NIC 1 10.10.10.1 NIC2 10.10.10.2 VIP 192.168.10.1
Basically I want either one of the NICs to ARP for the VIP. No load balancing required just HA. (2 Replies)
Discussion started by: wschmied
2 Replies
5. UNIX for Dummies Questions & Answers
Hi;
Is there a way to determine for sure how many NIC ports installed on my Linux box?
I tried to run "lspci" but not sure about the results, it's not clear.
Below are the results when i run both "ifconfig" & "lspci" on my Linux box i hope someone can help me finding the actual numbers of... (1 Reply)
Discussion started by: Katkota
1 Replies
6. Shell Programming and Scripting
Hi All,
I have bash script, so what is sintax script in bash for Enable and Disable Tab Key. Thanks for your help.:(
Thanks,
Rico (1 Reply)
Discussion started by: carnegiex
1 Replies
7. Red Hat
Hi all Expertise,
I have following issue to solve,
SSL / TLS Renegotiation DoS (low) 222.225.12.13
Ease of Exploitation Moderate
Port 443/tcp
Family Miscellaneous
Following is the problem description:------------------
Description The remote service encrypts traffic using TLS / SSL and... (2 Replies)
Discussion started by: manalisharmabe
2 Replies
8. Red Hat
Hi,
I have to get into BIOS and disable onbaord NICS for an IBM server, can someone please help me out.
I tried hitting F1 when reboot to get into BIOS, but it seems like a setup screen and I dont see any option to disable NICS?
Thanks
Sam (0 Replies)
Discussion started by: sam4919
0 Replies
9. IP Networking
Hi all,
Host - Ubuntu 12.04 desktop 64bit
Virtualizer - Oracle VirtualBox
2 NICs
Where can I find relevant document to set up 2 NICs, one for inward bound and another for outward bound, separate channel, both connected to the same router
Would following document be appropriate for my... (1 Reply)
Discussion started by: satimis
1 Replies
10. UNIX for Dummies Questions & Answers
Hello All,
I have Linux box with two interface cards.
Every card has it's own IP Address and Gateway, IP addresses are from different subnets.
eth0 192.168.1.10/24 GW 192.168.1.1
eth1 192.168.2.10/24 GW 192.168.2.1
Third PC is located in 192.168.13.0/24 network and is trying to access... (2 Replies)
Discussion started by: AndreiM
2 Replies
LEARN ABOUT LINUX
pnpbios
PNPBIOS(4) BSD/i386 Kernel Interfaces Manual PNPBIOS(4)
NAME
pnpbios -- support for embedded devices on the motherboard
DESCRIPTION
The pnpbios driver enumerates embedded ISA devices on the motherboard whose BIOS supports ``Plug and Play BIOS Specification''. It assigns
ISA bus resources (interrupt line, DMA channel, I/O ports, and memory region) to each device and activates it.
If it cannot assign necessary resources to a device without causing conflict with other devices in the system, the device will not be acti-
vated and will be unavailable to programs.
CAVEATS
There is no explicit way to disable individual embedded devices. The pnpbios driver will find all devices reported by the ``Plug and Play
(PnP)'' BIOS and try to activate them all.
There is no way to explicitly assign particular resource to a device. The resource assignment is fully automatic and there is no provision
for manual override.
SEE ALSO
pnp(4)
STANDARDS
Compaq, Phenix, and Intel, Plug and Play BIOS Specification Version 1.0A, May 5, 1994.
Compaq, Phenix, and Intel, Plug and Play BIOS CLARIFICATION Paper for Plug and Play BIOS Specification Version 1.0A, October 6, 1994.
HISTORY
The pnpbios driver first appeared in FreeBSD 4.0.
AUTHORS
The pnpbios driver was written by Mike Smith.
BSD
September 20, 2001 BSD