10 More Discussions You Might Find Interesting
1. Solaris
Hi all,
this time I'd need a help from an advanced Solaris system admin :rolleyes:
I attached a HP StorageWorks Ultrium 215 Tape Drives - Overview - c00059530 - HP Business Support Center to my Sun E220R and it got recognized immediately (probe-scsi-all).
Now the operating system boot process... (8 Replies)
Discussion started by: pseudocoder
8 Replies
2. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
3. AIX
Dear all,
I have ultriam3 tape. It is connected my LPAR. I have that the Sl.Nos. and slot number. but run the cfmgr i am not getting the tape drive.
I have fired the command lsdev -Cc tape but no reply.
how will i configure the tape in LPAR?
Please suggest. It is very urgent. (3 Replies)
Discussion started by: pernasivam
3 Replies
4. SCO
I replaced a HP Superstore Dat 40 with another HP Superstore Dat 40, but my backupedge software keeps putting up error code 1 (device not found) I have tried reinstaling the drive as DAT Alad stp 0 6 0 0. I'm not a computer expert but willing to have a go. I went into Backupedge to try and format a... (2 Replies)
Discussion started by: James Zwecker
2 Replies
5. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
6. Solaris
I will be honest I am quite new to UNIX and Solaris so this may be a simple thing.
I have just purchased a Sun (rebranded HP obviously) DAT DDS3 SCSI tape drive for my Sun Ultra 10 running Solaris 10.
I have previously fitted a SCSI card to the box which has configured ok and can be seen from... (1 Reply)
Discussion started by: mattw
1 Replies
7. Solaris
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Discussion started by: ECBROWN
9 Replies
8. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
9. Filesystems, Disks and Memory
I'm researching a tape drive + backup software to work across my unix/linux network. Was thinking about a dds4 tape drive (sony's) on my solaris ultra2, with some kind of software that would work across the network to back up my other 2 solaris boxes, plus my 2 linux boxes. What do others use... (3 Replies)
Discussion started by: kymberm
3 Replies
10. UNIX for Dummies Questions & Answers
I'm running SCO OS 505 on a Compaq proliant 1600, and my tape drive will just not work. It was working properly and whent to Sh?ts when I tried to get the cd rom working. I have uninstalled any configured tape drive and rebooted and then configured a tape drive and rebooted still nothing. I'm... (4 Replies)
Discussion started by: kikkin
4 Replies
tcopy(1) User Commands tcopy(1)
NAME
tcopy - copy a magnetic tape
SYNOPSIS
tcopy source [destination]
DESCRIPTION
The tcopy utility copies the magnetic tape mounted on the tape drive specified by the source argument. The only assumption made about the
contents of a tape is that there are two tape marks at the end.
When only a source drive is specified, tcopy scans the tape, and displays information about the sizes of records and tape files. If a des-
tination is specified, tcopy makes a copies the source tape onto the destination tape, with blocking preserved. As it copies, tcopy pro-
duces the same output as it does when only scanning a tape.
The tcopy utility requires the use of Berkeley-compatible device names. For example,
example% tcopy /dev/rmt/1b /dev/rmt/2b
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWesu |
+-----------------------------+-----------------------------+
SEE ALSO
mt(1), ioctl(2), attributes(5)
NOTES
tcopy will only run on systems supporting an associated set of ioctl(2) requests.
SunOS 5.10 10 Mar 2000 tcopy(1)