10 More Discussions You Might Find Interesting
1. Solaris
Hi all,
this time I'd need a help from an advanced Solaris system admin :rolleyes:
I attached a HP StorageWorks Ultrium 215 Tape Drives - Overview - c00059530 - HP Business Support Center to my Sun E220R and it got recognized immediately (probe-scsi-all).
Now the operating system boot process... (8 Replies)
Discussion started by: pseudocoder
8 Replies
2. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
3. AIX
Dear all,
I have ultriam3 tape. It is connected my LPAR. I have that the Sl.Nos. and slot number. but run the cfmgr i am not getting the tape drive.
I have fired the command lsdev -Cc tape but no reply.
how will i configure the tape in LPAR?
Please suggest. It is very urgent. (3 Replies)
Discussion started by: pernasivam
3 Replies
4. SCO
I replaced a HP Superstore Dat 40 with another HP Superstore Dat 40, but my backupedge software keeps putting up error code 1 (device not found) I have tried reinstaling the drive as DAT Alad stp 0 6 0 0. I'm not a computer expert but willing to have a go. I went into Backupedge to try and format a... (2 Replies)
Discussion started by: James Zwecker
2 Replies
5. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
6. Solaris
I will be honest I am quite new to UNIX and Solaris so this may be a simple thing.
I have just purchased a Sun (rebranded HP obviously) DAT DDS3 SCSI tape drive for my Sun Ultra 10 running Solaris 10.
I have previously fitted a SCSI card to the box which has configured ok and can be seen from... (1 Reply)
Discussion started by: mattw
1 Replies
7. Solaris
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Discussion started by: ECBROWN
9 Replies
8. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
9. Filesystems, Disks and Memory
I'm researching a tape drive + backup software to work across my unix/linux network. Was thinking about a dds4 tape drive (sony's) on my solaris ultra2, with some kind of software that would work across the network to back up my other 2 solaris boxes, plus my 2 linux boxes. What do others use... (3 Replies)
Discussion started by: kymberm
3 Replies
10. UNIX for Dummies Questions & Answers
I'm running SCO OS 505 on a Compaq proliant 1600, and my tape drive will just not work. It was working properly and whent to Sh?ts when I tried to get the cd rom working. I have uninstalled any configured tape drive and rebooted and then configured a tape drive and rebooted still nothing. I'm... (4 Replies)
Discussion started by: kikkin
4 Replies
AMTAPE(8) System Manager's Manual AMTAPE(8)
NAME
amtape - user interface to Amanda tape changer controls
SYNOPSIS
amtape config command [ command options ]
DESCRIPTION
Amtape performs tape changer control operations. It uses the underlying tape changer script defined by the tpchanger option for a particu-
lar Amanda configuration as specified by the config argument.
Tape changers maintain a notion of the current and next slot for each configuration. These may or may not correspond to an actual physical
state of the device, but do tend to minimize searching through the tape storage slots. If the desired tape is in the current slot, it is
likely the next tape needed is in the next slot rather than at some random position in the storage slots.
See the amanda(8) man page for more details about Amanda.
COMMANDS
reset Reset the tape changer to a known state. The current slot is set to the first slot. Other device-specific side effects may occur.
Some gravity stackers need to be reset to the top position by hand. This command notifies Amanda the stacker is back in that posi-
tion.
eject If a tape is loaded in the drive, it is ejected and returned to the slot from which it was loaded.
clean If a cleaning tape is defined for the changer, it is used to clean the drive.
show Show the contents of all slots. This can be slow.
label label
Search for and load the Amanda tape with label label.
taper Perform the taper scan algorithm. Load the next tape in the configuration's tape sequence, or a fresh tape with a suitable label.
device Display the name of the current tape device on stdout.
current
Display the current slot.
update Update the changer label database, if it has one, to match the tapes now available.
slot slot
Eject any tape in the drive and put it away, then load the tape from slot slot and reset current.
slot current
Eject any tape in the drive and put it away, then load the tape from the current slot.
slot prev
Eject any tape in the drive and put it away, then load the tape from the previous slot and reset current.
slot next
Eject any tape in the drive and put it away, then load the tape from the next slot and reset current.
slot first
Eject any tape in the drive and put it away, then load the tape from the first slot and reset current.
slot last
Eject any tape in the drive and put it away, then load the tape from the last slot and reset current.
slot advance
Eject any tape in the drive and put it away. Advance current to the next tape, but do not load it.
This is useful with non-gravity stackers to unload the last tape used and set up Amanda for the next run. If you just use eject,
the current tape will be mounted again in the next run, where it will be rejected as being still in use, ejected and the next tape
requested. Using slot next followed by eject does an unnecessary mount.
Note: most changers optimize the slot commands to not eject the loaded tape if it is the one being requested.
AUTHOR
James da Silva <jds@cs.umd.edu>
University of Maryland, College Park
SEE ALSO
amanda(8)
AMTAPE(8)
