10 More Discussions You Might Find Interesting
1. Hardware
Hi i ahve a SCSI drive that it use to work but now is not working. The Sun machine can not read the drive. My question is there is any other way to get the data back from the SCSI drive? I think if i replace the chip board on teh SCSI drive it might help to just buy a new Board but there is any... (4 Replies)
Discussion started by: percel
4 Replies
2. Hardware
I've had a scsi hard drive, scsi tape drive, and cd rom working off an adaptec 29160 controller. Everything worked great until a few days ago. I begin getting tar format errors (running sco 5.0.6) on the tape drive and occasionally the entire system would hang up while trying to access data on... (0 Replies)
Discussion started by: powwm
0 Replies
3. Filesystems, Disks and Memory
I have 2 dead SCSI drives. Can anyone tell me a good way to repair the disks??? Please! (1 Reply)
Discussion started by: disturbe_d
1 Replies
4. UNIX for Dummies Questions & Answers
Someone gave me a small external SCSI hard drive for my SunOS 5.8 test system. How do I make Unix see the hard drive? (2 Replies)
Discussion started by: FredSmith
2 Replies
5. Filesystems, Disks and Memory
Hi
I have 2 75GB SCSI hard drives and 2 250GB SATA hard drives which are using RAID Level 1 respectively. I wana have both FTP and Apache installed on them as services. I'm wondering what's the best partitioning schem? I wana use FC3 as my OS, so, I thought I can use the 75GB hard drive as the /... (0 Replies)
Discussion started by: sirbijan
0 Replies
6. Filesystems, Disks and Memory
I have an sco unix v/386 version 4.26 open server. I need to add a 2nd scsi hard drive. I don't know how to partition & format it as a bootable drive & mount it.
I know this is easy but I'm not familiar.
Thanks (1 Reply)
Discussion started by: bluebourbon
1 Replies
7. HP-UX
Does anyone know of a site that documents the various addressing schemes used with SCSI floppy disk drives? (5 Replies)
Discussion started by: Drew_Harrison
5 Replies
8. Filesystems, Disks and Memory
Need to change the partitions on a SCSI drive with Nextstep.
df shows
filesystem kbytes used avail cap mounted on
/dev/sd0a 2051824 231924 13% /
/dev/sd0b 998332 9 0% /Vol2
/dev/sd0c 998332 9 0% /Vol3
/dev/sd0d 998332 9 0% /Vol4
/dev/sd0e 998332 9 0% /Vol5... (3 Replies)
Discussion started by: Mace
3 Replies
9. UNIX for Dummies Questions & Answers
Adding another scsi drive, no name, it came with the instruction manual in japanese, so of no use. We need to format it, it only shows up as 14 gigs, when we know it is a 40 gig drive, but have no specs on the cyl, etc. Combing through faqs, one of my coworkers found a blurb that unix won't... (1 Reply)
Discussion started by: kymberm
1 Replies
10. UNIX for Dummies Questions & Answers
I'm running SCO OS 505 on a Compaq proliant 1600, and my tape drive will just not work. It was working properly and whent to Sh?ts when I tried to get the cd rom working. I have uninstalled any configured tape drive and rebooted and then configured a tape drive and rebooted still nothing. I'm... (4 Replies)
Discussion started by: kikkin
4 Replies
SC(4) BSD Kernel Interfaces Manual SC(4)
NAME
sc -- Sun Sun-2 SCSI bus host adaptor driver
SYNOPSIS
sun2
sc0 at mbmem0 addr 0x80000 ipl 2
sc1 at mbmem0 addr 0x84000 ipl 2
sun2 and sun4
sc0 at vme0 addr 0x200000 irq 2 vec 0x40
DESCRIPTION
The sc driver provides support for the Sun Microsystems "Sun-2" SCSI Bus Controller chipset found on various VME boards (Sun part #s
501-1045, 501-1138, 501-1149, and 501-1167) and on the "Sun-2 SCSI/Serial" (Sun part # 501-1006) Multibus board.
All versions of this driver can be configured with a flags directive in the config(1) file. The values are bits in a bitfield, and are
interpreted as follows:
0x0ff Set bit (1<<target) to disable SCSI parity checking
0x100 Set this bit to disable DMA interrupts (poll)
0x200 Set this bit to disable DMA entirely (use PIO)
For example: "flags 0x1ff" would disable DMA interrupts, and disable parity checking for targets 0-7. The "target" is the SCSI ID number of
a particular device on a particular SCSI bus.
SEE ALSO
cd(4), ch(4), intro(4), scsi(4), sd(4), st(4)
AUTHORS
Matt Fredette <fredette@NetBSD.org>,
David Jones,
Gordon Ross <gwr@NetBSD.org>,
Adam Glass <glass@NetBSD.org>,
Jason R. Thorpe <thorpej@NetBSD.org>.
BUGS
This SCSI chipset is rumored to have bugs in its handling of SCSI parity, therefore it is recommended that you disable parity on all SCSI
devices connected to this controller, and configure it with a 0x0ff value for its flags directive in the config(1) file.
This chipset has no support for raising the ATN signal, so there is no way to ever schedule a MSG_OUT phase on the bus. Currently, the
driver will ultimately reset the bus if this phase is ever requested by the upper layer SCSI driver.
This chipset has no support for SCSI disconnect/reselect. This means that slow devices, such as tape drives, can hog, or "lock up" the SCSI
bus.
This driver has not been tested in combination with non-SCSI devices behind Emulex or Adaptec bridges, which are common in Sun 2s and in Sun
Shoebox-type configurations. These devices pre-date the SCSI-I spec, and might not behave the way the chipset code currently expects.
BSD
June 28, 2001 BSD