10 More Discussions You Might Find Interesting
1. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
2. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
3. Solaris
I am using telnet instead of ssh because network/physical service is on maintenance mode. I can ping google and other internel machines. I can't ssh to this server because network/physical is dependency of ssh.
How can I fix this service. I can use network service but it is maintenance mode.... (8 Replies)
Discussion started by: getrue
8 Replies
4. Solaris
After a memory upgrade all network interfaces are misconfigued. How do i resolve this issue. Below are some out puts.thanks.
ifconfig: plumb: SIOCLIFADDIF: eg000g0:2: no such interface
# ifconfig eg1000g0:2 plumb
ifconfig: plumb: SIOCLIFADDIF: eg1000g0:2: no such interface
# ifconfig... (2 Replies)
Discussion started by: andersonedouard
2 Replies
5. Solaris
Hi, all!
Can anybody tell me how can I reset network statistic, which could be
seen by command 'netstat -i' or 'dladm show-dev -s'?
Thank you for advance
Christian (2 Replies)
Discussion started by: Inventor
2 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Solaris
hi experts,
i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display :
WARNING: ce0: fault detected external to device; service degraded
WARNING: ce0: xcvr addr:0x01 - link down
configuring IPv4... (2 Replies)
Discussion started by: bucci
2 Replies
8. Solaris
How do you test the physical network connection of an interface in solaris. I know that if you have an active connection and the cable gets yanked, you can look in the messages file to check for link failure messages. But is there any better way to see if you have good layer 2 connectivity? (1 Reply)
Discussion started by: tjlst15
1 Replies
9. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
10. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
IFDHPowerICC(3SMARTCARD) Smartcard Library Functions IFDHPowerICC(3SMARTCARD)
NAME
IFDHPowerICC - power up or power down the smart card
SYNOPSIS
#include <smartcard/ifdhandler.h>
RESPONSECODE IFDHPowerICC(DWORD Lun, DWORD Action, PUCHAR Atr, PDWORD AtrLength);
PARAMETERS
The IFDHPowerICC() takes the following parameters:
Input
Lun Logical Unit Number
Action Action to be taken
AtrLength Maximum length of the ATR
Output
Atr Answer to Reset (ATR) value of the inserted card
AtrLength Actual length of the ATR
DESCRIPTION
The IFDHPowerICC() function controls the power and reset signals of the ICC (smart card) at the reader or slot specified by Lun. The
Action parameter can take one of the following values:
IFD_POWER_UP Power and reset the card. Return the ATR and its length.
IFD_POWER_DOWN Power down the card. The Atr and AtrLength parameters are set to 0.
IFD_RESET Perform a quick reset on the card. Return the ATR and its length.
The IFD handler caches the ATR during a power up or reset and returns the ATR and its length in a call to IFDHGetCapabilities(3SMARTCARD).
Memory cards without an ATR return IFD_SUCCESS on power up or reset but Atr and AtrLength are set to 0.
RETURN VALUES
The following values are returned:
IFD_SUCCESS Successful completion.
IFD_ERROR_POWER_ACTION An error occurred while powering up or resetting the card.
IFD_NOT_SUPPORTED The action specified by Action is not supported.
IFD_COMMUNICATION_ERROR An error occurred.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
IFDHCreateChannelByName(3SMARTCARD), IFDHGetCapabilities(3SMARTCARD), attributes(5)
NOTES
This manual page is derived from the MUSCLE PC/SC IFD Driver Developer Kit documentation. License terms and attribution and copyright
information for this interface are available at the default location /var/sadm/pkg/SUNWocfh/install/copyright. If the Solaris Operating
Environment has been installed anywhere other than the default location, modify the path to access the file at the installed location.
SunOS 5.10 4 Dec 2002 IFDHPowerICC(3SMARTCARD)