10 More Discussions You Might Find Interesting
1. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
2. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
3. Solaris
I am using telnet instead of ssh because network/physical service is on maintenance mode. I can ping google and other internel machines. I can't ssh to this server because network/physical is dependency of ssh.
How can I fix this service. I can use network service but it is maintenance mode.... (8 Replies)
Discussion started by: getrue
8 Replies
4. Solaris
After a memory upgrade all network interfaces are misconfigued. How do i resolve this issue. Below are some out puts.thanks.
ifconfig: plumb: SIOCLIFADDIF: eg000g0:2: no such interface
# ifconfig eg1000g0:2 plumb
ifconfig: plumb: SIOCLIFADDIF: eg1000g0:2: no such interface
# ifconfig... (2 Replies)
Discussion started by: andersonedouard
2 Replies
5. Solaris
Hi, all!
Can anybody tell me how can I reset network statistic, which could be
seen by command 'netstat -i' or 'dladm show-dev -s'?
Thank you for advance
Christian (2 Replies)
Discussion started by: Inventor
2 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Solaris
hi experts,
i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display :
WARNING: ce0: fault detected external to device; service degraded
WARNING: ce0: xcvr addr:0x01 - link down
configuring IPv4... (2 Replies)
Discussion started by: bucci
2 Replies
8. Solaris
How do you test the physical network connection of an interface in solaris. I know that if you have an active connection and the cable gets yanked, you can look in the messages file to check for link failure messages. But is there any better way to see if you have good layer 2 connectivity? (1 Reply)
Discussion started by: tjlst15
1 Replies
9. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
10. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
OPENSC-TOOL(1) OpenSC tools OPENSC-TOOL(1)
NAME
opensc-tool - generic smart card utility
SYNOPSIS
opensc-tool [OPTIONS]
DESCRIPTION
The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
sending arbitrary APDU commands to a card.
OPTIONS
--info, -i
Print information about OpenSC, such as version and enabled components
--atr, -a
Print the Answer To Reset (ATR) of the card, output is in hex byte format
--name, -n
Print the name of the inserted card (driver)
--serial
Print the card serial number (normally the ICCSN), output is in hex byte format
--send-apdu apdu, -s apdu
Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF...
--list-files, -f
Recursively lists all files stored on card
--list-readers, -l
Lists all configured readers
--list-drivers, -D
Lists all installed card drivers
--reader num, -r num
Use the given reader number. The default is 0, the first reader in the system.
--card-driver driver, -c driver
Use the given card driver. The default is auto-detected.
--wait, -w
Wait for a card to be inserted
--verbose, -v
Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.
SEE ALSO
opensc-explorer(1)
opensc 06/03/2012 OPENSC-TOOL(1)