10 More Discussions You Might Find Interesting
1. AIX
Would anyone please kindly help to solve this problem...
An LPAR with the below network configuration. ent0 and ent1 are logical lan (virtual ethernet) from VIO SEA.
en0
1.2.3.4 <- boot ip
192.168.1.1 <- persistent ip
192.168.1.10 <- service ip
en1
11.22.33.44 <- boot ip
When I... (6 Replies)
Discussion started by: skeyeung
6 Replies
2. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
3. Gentoo
How to failover the cluster ? GNU/Linux
By which command,
My Linux version
2008 x86_64 x86_64 x86_64 GNU/Linux
What are the prerequisites we need to take while failover ?
if any
Regards (3 Replies)
Discussion started by: sidharthmellam
3 Replies
4. IP Networking
All,
I am looking to setup a simple IP failover setup, but it seems every place i look has some difficult setup like pacemaker or LVS.
I only want to handle the IP piece to failover a VIP.
Any suggestions? I checked out keepalived and that my work for me. (4 Replies)
Discussion started by: markdjones82
4 Replies
5. Solaris
Hi guys,
I'm running vxdmp and powerpath at the same time. Vxdmp for internal disks and powerpath for external.
The problem is that, on the failover tests which a fiber cable should be removed, the system cannot recognize the disks.
Any hints on how to configure powerpath in order to... (4 Replies)
Discussion started by: glenioborges
4 Replies
6. Solaris
The active NIC has been failing back and forth on two of our T2000s. I don't know when the problem originally began, but I can see failovers in the messages.* files. The network guy says the switches are clean (no errors) so I'm left looking at the configuration or any other issue that may be... (5 Replies)
Discussion started by: dangral
5 Replies
7. AIX
Hi All,
How do I failover on the ip load balancer (back and forth)? It involves first to load a new config on the passive ip. If success, load the new config on the ip active (which is now passive).
Any idea, please.
Thanks in advance. (0 Replies)
Discussion started by: itik
0 Replies
8. UNIX for Advanced & Expert Users
Hi,
I have 3 directories (/1 /2 and /3) with same contents and want to achieve fail over among them.
The Solution i thought of:
1. link /data to /1 (and provide users with /data to access)
2. CRON a script (to run every minute) to verify if /1 exist or not, if it does not exist (or its... (3 Replies)
Discussion started by: prvnrk
3 Replies
9. AIX
Hello All,
Here is a snipet from our cluster.log, I was wondering if anyone could shed some light on what may have caused the failover.
The first two lines indicate a possible memory issue which I am currently looking into.
Thanks. (0 Replies)
Discussion started by: Wez
0 Replies
10. Solaris
Would anyone know why a V440 Solaris 9 machine's interfaces (ce0 and ce1)
will not failover?
Both interfaces are on the same subnet, but different IPs. I can pull the plug on once interface (ce0) and ce1 will be accessible. I can reverse it and pull ce1, and ce0 will NOT be accessible. ... (5 Replies)
Discussion started by: StorageGuy
5 Replies