Login or Register to Ask a Question and Join Our Community


AIX

How to determine if there is a Power Problem using DIAG command?

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Operating Systems AIX How to determine if there is a Power Problem using DIAG command?
# 1  
Old 03-11-2008
How to determine if there is a Power Problem using DIAG command?
Hi guys can someone show me on how to use DIAG command in determining if there is really a power problem aside from errpt report?
# 2  
Old 03-11-2008
diag
advanced diags
system verification
highlight sysplanar0
enter to select it
f7 to run the diags.

Read the output with care, it can be confusing if you already have errpt entries for a power problem.

If you use diags, task selection, log a repair to sysplanar0 before you begin then the diags in system verification will ignore the errpt entries logged before the repair action was logged and just test the system and let you know if a problem was found.
# 3  
Old 03-18-2008
Thanks Duke
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. UNIX for Beginners Questions & Answers

Another one line command where I'd like to determine if Ubuntu or Red Hat when running command

Hello Forum, I'm making very good progress on my report thanks to the very helpful people on this forum. I've been able to successfully create my report for my Red Hat servers. But I do have a few ubuntu servers in the mix and I'd like to capture some data from them when an ssh connection is... (8 Replies)
Discussion started by: greavette
8 Replies

2. AIX

Determine power family of p system from the model #.

Folks, Again a very silly question :D Could someone tell me, how to determine the power family(540, 520, 575, 595 etc) just by looking into the model # info from prtconf/lsconf o/p of the lpar? I dont want run a search on any search engine to find out the power family or hit IBM website to... (3 Replies)
Discussion started by: thisissouvik
3 Replies

3. AIX

AIX power problem cron message on screen

Hello, I keep getting this message even after i removed it from the cron enteries it was added automatically Broadcast message from root@oradb (tty) at 12:00:00 ... rc.powerfail:2::WARNING!!! The system is now operating with a power problem. This message will be walled every 12... (2 Replies)
Discussion started by: filosophizer
2 Replies

4. UNIX for Dummies Questions & Answers

problem to determine all files and dir match up on 2 different unix boxes

Hi Friends I have 2 solaris boxes and I need to check certain directories (on local filesystem and mounted nfs) to make sure that they match up on both boxes and to delete or move the other mismatches to elsewhere on the local filesystem. I investigated for unix commands like rsync, and tree... (1 Reply)
Discussion started by: mpc8250
1 Replies

5. AIX

diag report

Hello Everybody, we have a System Model: IBM,7017-S7A running AIX 4.3 Processor Type: PowerPC_RS64-II Number Of Processors: 4 I found while running "diag" the following errors. The Service Request Number(s)/Probable Cause(s) (causes are listed in descending order of... (3 Replies)
Discussion started by: karthikosu
3 Replies

6. Solaris

Booting up problem after power outage

hi guys, i'm new so don't bite too hard. having a problem booting up a V210 running sol9 on after a power outage... an init5 was done but not a init0 before the power cut... so now when booting up it gives the ff: SC Alert: Host System has Reset Probing system devices Probing memory... (2 Replies)
Discussion started by: lungsta
2 Replies

7. AIX

What's meaning of "POWER" in diag command.?

I ran 'diag' command to verify disk follow the below steps. DIAG------?task selection-------ssa service aid-----Link verification I found that there are 3 types of status. (Good, Failed and Power). scp2: pdisk23 D69E584F 0 16 Power scp2: pdisk19 D657E7A9 1 15 Power scp2: pdisk28... (1 Reply)
Discussion started by: pattarapongn
1 Replies

8. AIX

Command to determine Tape Type

I have 2 UNIX boxes and I need to determine whether or not they possess the same tape drive. What is the hardware command to determine what type of tape drive is present? Thx in advance. (4 Replies)
Discussion started by: Surdeymon
4 Replies

9. HP-UX

user diag ??

if user diag is removed with a -r will it delete usr/mds ? and if so will this prevent a system from booting? Any info would be greatly appreciated!! Thanks Brian (1 Reply)
Discussion started by: breigner
1 Replies
Login or Register to Ask a Question