10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi to all
Trying to find printer HP drivers for AIX version 7. HP.com only references Unix. Have drivers on an older IBM system Risc 6000, AIX 4.3, but not sure where the "tar" file exists for the printer collection. The new IBM I am trying to setup is a 710 Express Server. The printer is a... (0 Replies)
Discussion started by: ideprize
0 Replies
2. AIX
I am trying to use this command to eject the tape
mt -f /dev/rmt/0 unload
but it gives me error
mt -f /dev/rmt/0 unload
mt: 0511-575 unload is not a recognized subcommand.
Usage: mt Subcommand
Valid subcommands are:
weof
eof
fsf
bsf
... (5 Replies)
Discussion started by: filosophizer
5 Replies
3. Solaris
Hi all,
this time I'd need a help from an advanced Solaris system admin :rolleyes:
I attached a HP StorageWorks Ultrium 215 Tape Drives - Overview - c00059530 - HP Business Support Center to my Sun E220R and it got recognized immediately (probe-scsi-all).
Now the operating system boot process... (8 Replies)
Discussion started by: pseudocoder
8 Replies
4. SCO
Does anybody know where I can get Wangtek Tape Drive 5125EN SCO Drivers?
I know that Sco 3.2 r4.2 had it built into the distribution. (1 Reply)
Discussion started by: chedlee88-1
1 Replies
5. AIX
I was wondering if somebody knew of a website where printer drivers can be downloaded for AIX 5.3. Most of our printers are HP and the driver that is installed works properly. As of lately, our users have started to get other type of printers, including Multi-purpose devices. I am struggling to... (2 Replies)
Discussion started by: fabiogilr
2 Replies
6. AIX
Hello,
Under Linux (Cups) you can place an interface driver in:
/etc/cups/interfaces
.. which allows you to intercept printouts to a certain printer and then carry on with the printer.
Is there a similar function under AIX?
Thanks, (0 Replies)
Discussion started by: stuaz
0 Replies
7. Solaris
Can I do this live? Or, do I need to do a probe-scsi-all after doing a stop/A? (10 Replies)
Discussion started by: jgordon
10 Replies
8. AIX
Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
Discussion started by: Zim-Aix-Guru
4 Replies
9. UNIX for Dummies Questions & Answers
Please, I'm From Argentina, And I Need To Know If The Drivers Of Program Unix, Version 5.01 Is Compatible Whit Drivers Of The Printer Epson Fx-2190
Thanks, And I Hope Yuor Answer. (0 Replies)
Discussion started by: juan alberghina
0 Replies
10. AIX
I have a dlt tape drive on a AIX 5.1 machine, I have no idea how to backup to this thing, would I just mount it can copy over to it, not sure the commands or where to begin? Can anyone help, or point me to documentation.... (14 Replies)
Discussion started by: csaunders
14 Replies
AMTAPE(8) System Manager's Manual AMTAPE(8)
NAME
amtape - user interface to Amanda tape changer controls
SYNOPSIS
amtape config command [ command options ]
DESCRIPTION
Amtape performs tape changer control operations. It uses the underlying tape changer script defined by the tpchanger option for a particu-
lar Amanda configuration as specified by the config argument.
Tape changers maintain a notion of the current and next slot for each configuration. These may or may not correspond to an actual physical
state of the device, but do tend to minimize searching through the tape storage slots. If the desired tape is in the current slot, it is
likely the next tape needed is in the next slot rather than at some random position in the storage slots.
See the amanda(8) man page for more details about Amanda.
COMMANDS
reset Reset the tape changer to a known state. The current slot is set to the first slot. Other device-specific side effects may occur.
Some gravity stackers need to be reset to the top position by hand. This command notifies Amanda the stacker is back in that posi-
tion.
eject If a tape is loaded in the drive, it is ejected and returned to the slot from which it was loaded.
clean If a cleaning tape is defined for the changer, it is used to clean the drive.
show Show the contents of all slots. This can be slow.
label label
Search for and load the Amanda tape with label label.
taper Perform the taper scan algorithm. Load the next tape in the configuration's tape sequence, or a fresh tape with a suitable label.
device Display the name of the current tape device on stdout.
current
Display the current slot.
update Update the changer label database, if it has one, to match the tapes now available.
slot slot
Eject any tape in the drive and put it away, then load the tape from slot slot and reset current.
slot current
Eject any tape in the drive and put it away, then load the tape from the current slot.
slot prev
Eject any tape in the drive and put it away, then load the tape from the previous slot and reset current.
slot next
Eject any tape in the drive and put it away, then load the tape from the next slot and reset current.
slot first
Eject any tape in the drive and put it away, then load the tape from the first slot and reset current.
slot last
Eject any tape in the drive and put it away, then load the tape from the last slot and reset current.
slot advance
Eject any tape in the drive and put it away. Advance current to the next tape, but do not load it.
This is useful with non-gravity stackers to unload the last tape used and set up Amanda for the next run. If you just use eject,
the current tape will be mounted again in the next run, where it will be rejected as being still in use, ejected and the next tape
requested. Using slot next followed by eject does an unnecessary mount.
Note: most changers optimize the slot commands to not eject the loaded tape if it is the one being requested.
AUTHOR
James da Silva <jds@cs.umd.edu>
University of Maryland, College Park
SEE ALSO
amanda(8)
AMTAPE(8)