8 More Discussions You Might Find Interesting
1. Solaris
Hi
I am having two node cluster. I was trying to change the to use scsi3 reservation for all disks having two paths. Please let me know where I went wrong or there any issue to implement the same.
On node1
bash-3.2# cldev status
=== Cluster DID Devices ===
Device Instance ... (8 Replies)
Discussion started by: sb200
8 Replies
2. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
3. Red Hat
Hi,
I would like to know scsi id of hard drive, which command is used to find scsi id of hard drive and disk related information.
Regards
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
4. UNIX for Dummies Questions & Answers
hey guys this is my problem I have SCO unix installed on a IDE h/drive. I want to add a SCSI hard drive, how do i do that within UNIX (1 Reply)
Discussion started by: kwame.neilsen
1 Replies
5. Solaris
I have run init 0 to bring it to OK prompt.
I know that probe-scsi-all can hang the system.
I want to know what is the difference between probe-scsi-all and probe-scsi.
I was told that probe-scsi-all external and internal devices and probe-scsi shows only internal devices. what dose this ... (3 Replies)
Discussion started by: nitinkgoud
3 Replies
6. UNIX for Advanced & Expert Users
I would like to install a AIT drive to the scsi connector on our solaris box. I am very new to the unix world and would be greatful if someone could help or lead me in the right direction.
Thanks (4 Replies)
Discussion started by: vpyle
4 Replies
7. UNIX for Dummies Questions & Answers
Hello agian !
What is the difference between SCSI and IDE hard disks ?
I have Intel PC and when i check i have Generic IDE TYPE DISK0
is IDE hard disk is ok for Solrais ? or should i buy the SCSI hard disk ?
Thanks
Abid Malik (3 Replies)
Discussion started by: abidmalik
3 Replies
8. UNIX for Advanced & Expert Users
How can you get a scsi card to initalize or decome available at boot up on AIX 4.3 (1 Reply)
Discussion started by: truma1
1 Replies
ESIOP(4) BSD Kernel Interfaces Manual ESIOP(4)
NAME
esiop -- Enhanced Symbios Logic/NCR 53c8xx SCSI driver
SYNOPSIS
esiop* at pci? dev ? function ?
options SIOP_SYMLED
scsibus* at esiop?
DESCRIPTION
The esiop driver provides improved support over siop(4) for the Symbios Logic/NCR 53x8xx series of SCSI controller chips:
- 53c825 and 53c825a (Fast-Wide SCSI)
- 53c875 and 53c875j (Ultra-Wide SCSI)
- 53c876 (Dual Ultra-Wide SCSI)
- 53c885 (Ultra-Wide SCSI and Ethernet)
- 53c895 (Ultra2-Wide SCSI)
- 53c896 (PCI 64bit, dual Ultra2-Wide SCSI)
- 53c1010-33 (PCI 64bit, dual Ultra160 SCSI)
- 53c1510d (PCI 64bit, dual Ultra2-wide SCSI)
Older adapters are supported by the siop(4) driver.
The SIOP_SYMLED option causes the driver to report SCSI activity on the GPIO pin 1, which is connected to the activity LED on some adapters.
At this time only the 53c895 based Symbios and Tekram adapters are known to require this.
SEE ALSO
cd(4), ch(4), intro(4), pci(4), scsi(4), sd(4), siop(4), st(4), uk(4)
HISTORY
The esiop driver first appeared in NetBSD 1.6.
AUTHORS
The esiop driver was written by Manuel Bouyer <Manuel.Bouyer@lip6.fr> for NetBSD.
BSD
April 23, 2002 BSD
