#1 Connect to ASMI
#2 Configure the deconfigured memory
#3 Start the machine
OK, everything is fine, however now cannot connect to ASMI through browser,
using both HMC Ports
Default IP 1 = 192.168.2.147
Default IP 2 = 192.168.3.147
able to ping both IPs, did a reset of service processor from the control panel 9113-550 , pulled the power plug and started, still same problem
1- able to ping both service IPs
2- but unable to use any browser to connect it
OK, everything is fine, however now cannot connect to ASMI through browser,
using both HMC Ports
Default IP 1 = 192.168.2.147
Default IP 2 = 192.168.3.147
I haven't used an IBM p-Series without a HMC for such a long time that i am not sure i can help you off the top of my head here. However, there might be all sorts of problems putting obstacles into the IP-communication between your browser and the Serviceprocessor.
First off, it might be that the IP addresses have once been changed and i am not sure if a simple SP-reset really changes that back to the defaults. (That i am not sure means just that: i don't know. If you have information in the affirmative, then perhaps it is so.)
Second, there is a sure-fire way to connect to the SP, whatever its IP might be: go to the data centre, connect a crossed-out cable to the SP connector 1 or 2 and connect your system directly to it. I have a small netbook for these purposes with a Wireshark/Ethereal software installed, so i can identify even unknown or fogotten IP-adresses. Once you identified the IP-address you still need the ASMI password, which is, btw., completely separate!
but I am able to ping from my laptop/pc to the service IP address which is
Default IP 1 = 192.168.2.147
Default IP 2 = 192.168.3.147
Yes, the IPs are active. Who tells you for sure that they are the service processors? They could be all sorts of systems, yes?
Quote:
Originally Posted by filosophizer
and also going to IVM, I can get the IP address for ASMI
OK, you have highlighted something, let me highlight something for you in return ;-)
I'd say the IVM awaits the interface to be where you are trying to find them. But it is not any more successful in that venture than you are. Therefore, eliminate all possible problems and connect directly to the system with a cross-over cable as suggested. That is a sure-fire method and if this fails the box is a case for the technician.
I'd say the IVM awaits the interface to be where you are trying to find them. But it is not any more successful in that venture than you are. Therefore, eliminate all possible problems and connect directly to the system with a cross-over cable as suggested. That is a sure-fire method and if this fails the box is a case for the technician.
I hope this helps.
bakunin
Thanks, I have to try two things:
1- Reset Toggle which is on the board (not tried yet)
2- Cross Cable : May be that will work (just informing you, it was working with straight cable, then i reconfigured the deconfigured memory and then stopped connecting to ASMI via browser)
2- Cross Cable : May be that will work (just informing you, it was working with straight cable,
I should have paid more attention to the model number: older models needed a crossover cable, newer ones don't (or, more correctly: don't care - they work with both). As it worked with a normal cable the first time your hardware is obviously new enough to ve able to use both, so the cable is not the problem.
hi
I am having issues when trying to connect using ftp, I am having the following error:
User (10.100.48.73:(none)): moz
331 Password required for moza.
Password:
530 Login incorrect.
Login failed.
ftp> by
221 Goodbye.
I have created a user like this:
useradd -g 10 -d /lam/moza -m -s... (11 Replies)
Hello,
I just installed CentOS 7 (Server with GUI) and guess what I could install Virtual Box Guest additions without installing any extra package/software which is great news !
Now bad news or not so great news.
My Host OS is Windows 10, Virtual Box is the virtualization software. CentOS7-1... (0 Replies)
I have managed to install Broadcom BCM43228 Wireless adapter on a laptop running CentOS 5.9 using instructions at:
wiki.centos.org/HowTos/Laptops/Wireless/Broadcom
I had the problem "Error for wireless request "Set Encode" (8B2A): SET failed on device... mentioned on the same page and solved... (0 Replies)
I am trying to connect to SQL plus through unix but i am getting below error
'ksh: sqlplus: not found'
note i am running this from /home/xxx
do i need to set any environmental variable for this. below is my code
echo " hello world"
sqlplus -s apps/CAF78GEN<<EOF
set heading... (4 Replies)
Hi,
I'm trying to connect from an HP-UX with SSH2 client(ssh2 3.1.2 on hppa1.1-hp-hpux11.00) to an SSH2 server on a VxWorks system. The SSH connection is failing with the below connection logs:
> /usr/local/bin/ssh2 -v -l testuser 10.10.10.10
debug: Ssh2/ssh2.c:1391: Using file... (4 Replies)
Hi
I am facing very strange issue on my vio server 5 vio clients are confgured, now I am to connect 3 vio client , i am unable to connect 2 vio client my ip address,subnet mask,gateway is correct.
i have rebooted and reconfigured the ip address, but issue is persists.
Kindly suggest how to... (0 Replies)
Hi friends
How to clear the asmi deconfiguration errors.recently on cpu got deconfigured ibm assist to clear the error and to update the firmware please help me
raj (0 Replies)
I shall explain the situation that I am facing to the best extent possible. I require some help, as this situation is an urgent one.
I am trying to automate sending data from one AIX machine to another. A script runs that tries to push data received from an upstream application to another AIX... (7 Replies)
Hi friends
recently i have installed SXDE 1/08 into my machine,and i installed wifi driver also
its working fine,Recently i was unable to connect to Internet,I have not changed any configurations and any installations,thing is that i got my iwk0 interface is UP and IP address also and i can... (6 Replies)
Hello HP-UX Gurus,
I am having issues trying to start an x-session via eXceed 7.1.
When I bring up eXceed via XDMCP Braodcast I see the host name and IP Address but when I try to connect the X window does not come up.
I made the modification to the following file “/etc/dt/config/Xaccess”... (2 Replies)