10 More Discussions You Might Find Interesting
1. AIX
i've installed vios 2.2 on blade PS700
there are 2 disk, hdisk0 dan hdisk1 and i want to mirror it
but blv (boot logic volume) does not appear on hdisk1 (bootlist -mode normal -ls) only on hdisk0
i've already did command (bootlist -mode normal hdisk0 hdisk1"
does anyone know the command to... (1 Reply)
Discussion started by: jpmei
1 Replies
2. Hardware
I have a 320 GB drive which dual boots Windows and Debian:
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal):... (0 Replies)
Discussion started by: phillipsoasis
0 Replies
3. Shell Programming and Scripting
Hello,
I have a file like this:
FILE.TXT:
(define argc :: int)
(assert ( > argc 1))
(assert ( = argc 1))
<check>
#
(define c :: float)
(assert ( > c 0))
(assert ( = c 0))
<check>
#
now, i want to separate each block('#' is the delimeter), make them separate files, and then send them as... (5 Replies)
Discussion started by: paramad
5 Replies
4. UNIX for Dummies Questions & Answers
I'm Unix. I'm looking at "df" on Unix now and below is an example. It's lists the filesystems out in 512-blocks, I need this in 4k blocks. Is there a way to do this in Unix or do I manually convert and how?
So for container 1 there is 7,340,032 in size in 512-blocks. What would the 4k block be... (2 Replies)
Discussion started by: rockycj
2 Replies
5. UNIX for Advanced & Expert Users
Hi,
I want to have one binary image that contains both my boot loader as well as the OS(linux) image at pre defined offsets which i can use to program flash . Can anyone help in this direction?
Regards
Subrata (0 Replies)
Discussion started by: subratasaharia
0 Replies
6. Filesystems, Disks and Memory
Hello All,
I backed up my RHEL 4 as an image.
Then I restored the image on my machine. Everything went fine but I dont get the normal boot sequence as it used to come when I freshly installed RHEL4.
The messages that are shown when the system boots are something like-
" .....
EXT3-fs:... (2 Replies)
Discussion started by: shamik
2 Replies
7. Red Hat
I'm running redhat linux: 2.6.18-128.1.6.el5xen #1 SMP Tue Mar 24 12:28:27 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux as my Dom0.
I have several other DomU's running on this system, but for this test I've shut them down.
I'm attempting to boot winXP from an image.
Here is my config file:
#... (3 Replies)
Discussion started by: willjw1
3 Replies
8. AIX
hi all
i just found one of my p650 server showing a warning message when i
tried to run bosboot command after upgrading TL to AIX 530803.
i also tried to run chpv -c hdisk0 and chpv -c hdisk1 to clear out the
old boot info in hdisk0 and hdisk1 and rerun bosboot -a. it still
showed... (0 Replies)
Discussion started by: rs6000er
0 Replies
9. AIX
hello
i saved my system this morning, mksysb tape, and i have the message: "boot.image exceeded the size....." i have not the end because the message is disappeared.
where can i find the mksysb message in a log ?
the message is scary ?
thank you (6 Replies)
Discussion started by: pascalbout
6 Replies
10. Filesystems, Disks and Memory
Where can I find the boot floppy disk image file(*.vfd)of SCO UNIX 5.0.5?:confused: (1 Reply)
Discussion started by: whiteknight
1 Replies
HT(4) Kernel Interfaces Manual HT(4)
NAME
ht - RH-11/TU-16 magtape interface
DESCRIPTION
The files mt0, mt1, ... refer to the DEC RH/TM/TU16 magtape. When opened for reading or writing, the tape is not rewound. When closed,
it is rewound (unless the 0200 bit is on, see below). If the tape was open for writing, a double end-of-file is written. If the tape is
not to be rewound the tape is backspaced to just between the two tapemarks.
A standard tape consists of a series of 512 byte records terminated by a double end-of-file. To the extent possible, the system makes it
possible, if inefficient, to treat the tape like any other file. Seeks have their usual meaning and it is possible to read or write a byte
at a time. Writing in very small units is inadvisable, however, because it tends to create monstrous record gaps.
The last octal digit of the minor device number selects the drive. The middle digit selects a controller. The initial digit is even to
select 800 BPI, odd to select 1600 BPI. If the 0200 bit is on (initial digit 2 or 3), the tape is not rewound on close. Note that the
minor device number has no necessary connection with the file name, and in fact tp(1) turns the short name x into `/dev/mtx'.
The mt files discussed above are useful when it is desired to access the tape in a way compatible with ordinary files. When foreign tapes
are to be dealt with, and especially when long records are to be read or written, the `raw' interface is appropriate. The associated files
may be named rmt0, ..., rmt7, but the same minor-device considerations as for the regular files still apply.
Each read or write call reads or writes the next record on the tape. In the write case the record has the same length as the buffer given.
During a read, the record size is passed back as the number of bytes read, provided it is no greater than the buffer size; if the record is
long, an error is indicated. In raw tape I/O, the buffer must begin on a word boundary and the count must be even. Seeks are ignored. A
zero count is returned when a tape mark is read; another read will fetch the first record of the next tape file.
FILES
/dev/mt?, /dev/rmt?
SEE ALSO
tp(1)
BUGS
The magtape system is supposed to be able to take 64 drives. Such addressing has never been tried.
Taking a drive off line, or running off the end of tape, while writing have been known to hang the system.
If any non-data error is encountered, it refuses to do anything more until closed. In raw I/O, there should be a way to perform forward
and backward record and file spacing and to write an EOF mark explicitly.
HT(4)