10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I'm looking to copy a boot disk on an old Solaris 8 system using dd. I'll bring the system down to single user mode and begin from there. I'm copying my source disk to a larger target disk. Do I need to do anything other than the 'dd' command below because the target disk is bigger? ... (2 Replies)
Discussion started by: sparcman
2 Replies
2. Solaris
Hello,
I am creating a new disk using the following command:
dd if=/dev/zero of=/export/home/ramdisk/0 bs=512 count=4096k
after creating the disk, i tool a ufsdump of a solaris 10 filesytem (disk size 512MB)
ufsdump -cvf /export/home/ufsdump/sol_orig /and then restored the dump files onto... (10 Replies)
Discussion started by: Zam_1234
10 Replies
3. AIX
hello folks,
I have a 300GB ROOTVG volume groups with one filesystem /backup having 200GB allocated space
Now, I cannot alt disk clone or mirrorvg this hdisk with another smaller disk. The disk size has to be 300GB; I tried alt disk clone and mirrorvg , it doesn't work. you cannot copy LVs as... (9 Replies)
Discussion started by: filosophizer
9 Replies
4. AIX
Good Morning!
My p550 running AIX 5.3 TL9 SP6 is supposedly connected to its SAN. However, it's not configuring its luns or behaving like it sees any traffic at all.
"fcstat fcs0" and "fcstat fcs1" both indicate no traffic moving across the interfaces.
Does AIX have a basic command that... (4 Replies)
Discussion started by: dafydd2277
4 Replies
5. UNIX for Dummies Questions & Answers
I have found a question from the exercises of my study mat. The question is
"Why are there a in-core copy and a disk-copy of i-node block and super block?"
If any one know the proper answer then please send me..... (1 Reply)
Discussion started by: dearanik
1 Replies
6. UNIX for Dummies Questions & Answers
Would this be the right forum to ask basic unix administration questions relating to smitty tasks, etc? (2 Replies)
Discussion started by: NycUnxer
2 Replies
7. UNIX for Dummies Questions & Answers
Hello everybody, iam new to unix. here is a question i had.
when i run errpt -a , sample out put is as follows
LABEL: FCP_ARRAY_ERR4
IDENTIFIER: D5385D18
Date/Time: Mon Sep 25 11:15:59
Sequence Number: 182869
Machine Id: 000166784C00
Node Id: ... (0 Replies)
Discussion started by: karthikosu
0 Replies
8. AIX
how to i find out the disk usage on a server.
say in windows examples its like C:/ D:/ and checking out the disk space.
how can i find in Unix.
can i just use df -k (3 Replies)
Discussion started by: karthikosu
3 Replies
9. AIX
Morning, All
I've been doing some work on AIX print queues, troubleshooting some underlying issues we've been having. In the process of this I've uncovered some potential gaps in our knowledge. Our typical setup is remote impact printers (In this case OKIML5520s, with NICs) and local queues... (0 Replies)
Discussion started by: alexop
0 Replies
10. UNIX for Dummies Questions & Answers
Hi
Can some one help to understand the follwoing thing:
what is a simple mounting? for examle what the following lines says
/dev/hd2 /usr/xxx
if I have to install a software in a remote server, how i can use local cdrom to read the installation files from?
what about... (3 Replies)
Discussion started by: ajaya
3 Replies
diskscan(1M) System Administration Commands diskscan(1M)
NAME
diskscan - perform surface analysis
SYNOPSIS
diskscan [-W] [-n] [-y] raw_device
DESCRIPTION
diskscan is used by the system administrator to perform surface analysis on a portion of a hard disk. The disk portion may be a raw parti-
tion or slice; it is identified using its raw device name. By default, the specified portion of the disk is read (non-destructive) and
errors reported on standard error. In addition, a progress report is printed on standard out. The list of bad blocks should be saved in a
file and later fed into addbadsec(1M), which will remap them.
OPTIONS
The following options are supported:
-n Causes diskscan to suppress linefeeds when printing progress information on standard out.
-W Causes diskscan to perform write and read surface analysis. This type of surface analysis is destructive and should be invoked
with caution.
-y Causes diskscan to suppress the warning regarding destruction of existing data that is issued when -W is used.
OPERANDS
The following operands are supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?[ps]?. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
addbadsec(1M), disks(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)
NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the diskscan, addbad-
sec(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS format utility; however, to label, ana-
lyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 diskscan(1M)