10 More Discussions You Might Find Interesting
1. Linux
I just ran sudo service networking start on Ubuntu 16.00 and came out with error message
Job for networking service failed because control process exited with error code see systemctl status networking.service
I tried to also run this command
systemctl status networking.service
I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
2. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
3. UNIX for Dummies Questions & Answers
i need a one liner command that writes in /var/log/net.log the date when i connect to the network and when i disconect ..i know that i need to write somethin in /etc/network/interfaces but idk what ! please help (1 Reply)
Discussion started by: g0dlik3
1 Replies
4. UNIX for Advanced & Expert Users
All, I have a quad NIC on a V880 running Solaris 9. I've heard you can bond interfaces together and get better throughput. I found this link that seems to describe the process well. However, the command mentioned (dladm) is missing. Is there some package I need to install to get this command? Thx.... (2 Replies)
Discussion started by: agcodba
2 Replies
5. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
6. AIX
Hi,
I want to know wheather partition size for installation of vio client can be specified on vio server
example
If I am installing vio server on blade with 2*300gb hard disk,after that I want to create 2 vio client (AIX Operating system) wheather I can specify hard disk size while... (1 Reply)
Discussion started by: manoj.solaris
1 Replies
7. Solaris
I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies
8. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies
9. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies
10. Solaris
Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies
nca.if(4) File Formats nca.if(4)
NAME
nca.if - the NCA configuration file that specifies physical interfaces
SYNOPSIS
/etc/nca/nca.if
DESCRIPTION
Specify the physical interfaces for which the Solaris Network Cache and Accelerator ("NCA") feature will be configured in the nca.if con-
figuration file. List the physical interfaces in the file, one per line. To configure NCA to listen on all physical interfaces present on
the system backed by a hostname.{interface_name}, then list only an asterik ("*") in nca.if.
When the ncakmod(1) initialization script is invoked during system boot, it will attempt to configure each physical interface specified in
the nca.if file by using ncaconfd(1M). Note that there must be an accompanying hostname.{interface_name} file and an entry in /etc/hosts
for the contents of hostname.{interface_name}.
You must reboot in order to implement changes to the nca.if file.
EXAMPLES
x86
Example 1: nca.if on x86
The following is an example of an nca.if file that would be used on an x86 system:
iprb1
iprb6
iprb8
SPARC
Example 2: nca.if on SPARC
The following is an example of an nca.if file that would be used on a SPARC system:
hme2
hme3
hme4
All Platforms
Example 3: Configuring NCA to Listen on All Physical Interfaces
The following example shows the contents of an nca.if file that would be used to configure either platform to listen on all physical inter-
faces present on the system:
*
FILES
/etc/nca/nca.if Lists the physical interfaces on which NCA will run.
/etc/hostname.{}{0-9} Lists all physical interfaces configured on the server.
/etc/hosts Lists all host names associated with the server. Entries in this file must match with entries in /etc/host-
name.{}{0-9} for NCA to function.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWncar |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
nca(1), ncab2clf(1), ncakmod(1), ifconfig(1M), ncakmod.conf(4), ncalogd.conf(4), attributes(5)
System Administration Guide: IP Services
SunOS 5.10 18 Feb 2003 nca.if(4)