Changing the default network Interface Post: 95700

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

2. UNIX for Dummies Questions & Answers

Changing Network Interface hme1 to hme0

I have sun solaris 9 installed but I have the interface configured to hme1 instead of hme0, our default value. Is there a way where i can rename the existing/working hme1 to hme0...? I want to showup the hmeo up if i say ifconfig -a.. rite now i see the hme1 up.. please advice if possible...

3. Solaris

Network interface issue

Hi All, I want to configure network into my system. i tried following in to configure the interface to find the name of interface #prtdiag |grep net i got following 0 PCI-1 33 1 network-SUNW, hme then i tried following #prtconf -v |grep net network, instance #0

4. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

5. Solaris

Network Interface -- Solaris

Dear All, I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface . The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped. But i find that no of Input and Output...

6. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

7. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT CENTOS

opensc-tool

OPENSC-TOOL(1)							   OpenSC Tools 						    OPENSC-TOOL(1)

NAME

       opensc-tool - generic smart card utility

SYNOPSIS

       opensc-tool [OPTIONS]

DESCRIPTION

       The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
       sending arbitrary APDU commands to a card.

OPTIONS

       --atr, -a
	   Print the Answer To Reset (ATR) of the card. Output is in hex byte format

       --card-driver driver, -c driver
	   Use the given card driver. The default is auto-detected.

       --info, -i
	   Print information about OpenSC, such as version and enabled components.

       --list-drivers, -D
	   List all installed card drivers.

       --list-files, -f
	   Recursively list all files stored on card.

       --list-readers, -l
	   List all configured readers.

       --name, -n
	   Print the name of the inserted card (driver).

       --reader num, -r num
	   Use the given reader number. The default is 0, the first reader in the system.

       --send-apdu apdu, -s apdu
	   Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF....

       --serial
	   Print the card serial number (normally the ICCSN). Output is in hex byte format

       --verbose, -v
	   Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.

       --wait, -w
	   Wait for a card to be inserted.

SEE ALSO

       opensc-explorer(1)

opensc								    06/17/2014							    OPENSC-TOOL(1)