10-25-2001
For SUN, what I previously posted should get you going.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
5. Solaris
I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me:
SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
Hi Group,
I Have just installed quad card in my V440 machine,
I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able,
here is details of my machine.
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index
1
... (2 Replies)
Discussion started by: sameergrover
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Hardware
Dear all,
I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card.
I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies
LEARN ABOUT CENTOS
rdma_post_recv
RDMA_POST_RECV(3) Librdmacm Programmer's Manual RDMA_POST_RECV(3)
NAME
rdma_post_recv - post a work request to receive an incoming message.
SYNOPSIS
#include <rdma/rdma_verbs.h>
int rdma_post_recv (struct rdma_cm_id *id, void *context, void *addr, size_t length, struct ibv_mr *mr);
ARGUMENTS
id A reference to a communication identifier where the message buffer will be posted.
context User-defined context associated with the request.
addr The address of the memory buffer to post.
length The length of the memory buffer.
mr A registered memory region associated with the posted buffer.
DESCRIPTION
Posts a work request to the receive queue of the queue pair associated with the rdma_cm_id. The posted buffer will be queued to receive an
incoming message sent by the remote peer.
RETURN VALUE
Returns 0 on success, or -1 on error. If an error occurs, errno will be set to indicate the failure reason.
NOTES
The user is responsible for ensuring that a receive buffer is posted and large enough to contain all sent data before the peer posts the
corresponding send message. The message buffer must have been registered before being posted, with the mr parameter referencing the regis-
tration. The buffer must remain registered until the receive completes.
Messages may be posted to an rdma_cm_id only after a queue pair has been associated with it. A queue pair is bound to an rdma_cm_id after
calling rdma_create_ep or rdma_create_qp, if the rdma_cm_id is allocated using rdma_create_id.
The user-defined context associated with the receive request will be returned to the user through the work completion wr_id, work request
identifier, field.
SEE ALSO
rdma_cm(7), rdma_create_id(3), rdma_create_ep(3), rdma_create_qp(3), rdma_reg_read(3), ibv_reg_mr(3), ibv_dereg_mr(3), rdma_post_recvv(3),
rdma_post_send(3)
librdmacm 2010-07-19 RDMA_POST_RECV(3)