10-25-2001
For SUN, what I previously posted should get you going.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
5. Solaris
I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me:
SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
Hi Group,
I Have just installed quad card in my V440 machine,
I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able,
here is details of my machine.
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index
1
... (2 Replies)
Discussion started by: sameergrover
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Hardware
Dear all,
I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card.
I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies
LEARN ABOUT SUNOS
dat_ep_reset
dat_ep_reset(3DAT) Direct Access Transport Library Functions dat_ep_reset(3DAT)
NAME
dat_ep_reset - transition the local Endpoint from a Disconnected to an Unconnected state
SYNOPSIS
cc [ flag... ] file... -ldat [ library... ]
#include <dat/udat.h>
DAT_RETURN
dat_ep_reset (
IN DAT_EP_HANDLE ep_handle
)
PARAMETERS
ep_handle Handle for an instance of Endpoint.
DESCRIPTION
The dat_ep_reset() function transitions the local Endpoint from a Disconnected to an Unconnected state.
The operation might cause the loss of any completions of previously posted DTOs and RMRs that were not dequeued yet.
The dat_ep_reset() function is valid for both Disconnected and Unconnected states. For Unconnected state, the operation is no-op because
the Endpoint is already in an Unconnected state. For an Unconnected state, the preposted Recvs are not affected by the call.
RETURN VALUES
DAT_SUCCESS The operation was successful.
DAT_INVALID_HANDLE ep_handle is invalid.
DAT_INVALID_STATE Parameter in an invalid state. Endpoint is not in the valid state for reset.
USAGE
If the Consumer wants to ensure that all Completions are dequeued, the Consumer can post DTO or RMR operations as a "marker" that are
flushed to recv_evd_handle or request_evd_handle. Now, when the Consumer dequeues the completion of the "marker" from the EVD, it is guar-
anteed that all previously posted DTO and RMR completions for the Endpoint were dequeued for that EVD. Now, it is safe to reset the End-
point without losing any completions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Interface Stability |Standard: uDAPL, 1.1, 1.2 |
+-----------------------------+-----------------------------+
|MT-Level |Unsafe |
+-----------------------------+-----------------------------+
SEE ALSO
libdat(3LIB), attributes(5)
SunOS 5.10 16 Jul 2004 dat_ep_reset(3DAT)