12-16-2005
haven't worked with sco professionally so this is just a guess ---
if this has never worked, do you folks have the correct driver software for the tape drive?
if this has just recently went bonkers, what changed recently that might have affected the hardware drivers and/or the OS?
good luck!
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi guys
I had a system running 5.0.6 , we upgraded it to 5.0.7 everything was fine till i try to do a test backup.
The error was cannot open (cannot open /dev/xct0 no such file or directory)what i did was, removed the tape , reboot the system and the try to install it again, but its... (2 Replies)
Discussion started by: josramon
2 Replies
2. UNIX for Dummies Questions & Answers
I need to run a back up that will take more than one tape. What is the command that will continue the back up on to a second tape drive. the first is /dev/rStp0 second is /dev/rStp1. Anyone? (1 Reply)
Discussion started by: franruiz
1 Replies
3. UNIX for Dummies Questions & Answers
hi guys,
I.m trying to remove and add a new tape drive by using the mkdev tape command and when i try to update the Kernel this is what i'm getting,
i386ld: Symbol Sdsk_no_tag in /var/opt/K/SCO/link/1.1.1Eb/etc/conf/pack.d/blad/s
pace.o is multiply defined. First defined in... (0 Replies)
Discussion started by: josramon
0 Replies
4. SCO
Situation - i have an IDE hard drive from server apparently running SCO last used in 2003. No access to computer it was formerly in. I need to access the drive to pull off data files from a billing/scheduling program. I have no SCO machine or access to one atm. Have some limited Linux... (3 Replies)
Discussion started by: lordlars1
3 Replies
5. SCO
Hi,
Does anyone know if a HP VS160 Tape drive will work with SCO Openserver Release 5?
If so what driver would it use? alad, cha?
Thanks
John (3 Replies)
Discussion started by: jfd7000
3 Replies
6. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
7. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
8. SCO
Our tape drive died and I installed a newer Quantum DAT72 drive in it's place with the same SCSI ID. It still works, but with one major flaw, the system will lock up if I try to upgrade BackupEDGE or view NFS settings in scoadmin.
I get a Transition to ready failure on ha=0* message when the... (4 Replies)
Discussion started by: psytropic
4 Replies
tz(4) Kernel Interfaces Manual tz(4)
Name
tz - SCSI magnetic tape interface
Syntax
VAX NCR 5380:
adapter uba0 at nexus?
controller scsi0 at uba0 csr 0x200c0080 vector szintr
tape tz0 at scsi0 drive 0
VAX DEC SII:
adapter ibus0 at nexus?
controller sii0 at ibus? vector sii_intr
tape tz0 at sii0 drive 0
RISC DEC SII:
adapter ibus0 at nexus?
controller sii0 at ibus? vector sii_intr
tape tz0 at sii0 drive 0
RISC DEC KZQ:
adapter uba0 at nexus?
controller kzq0 at ibus? csr 0761300vector sii_intr
tape tz0 at kzq0 drive 0
RISC NCR ASC:
adapter ibus0 at nexus?
controller asc0 at ibus? vector ascintr
tape tz0 at asc0 drive 0
Description
The SCSI tape driver provides a standard tape drive interface as described in This is a driver for any Digital SCSI tape device.
For the TZK10 QIC format tape drive, the densities supported are QIC-24 (read only) block size of 512 byte blocks, QIC-120, and QIC-150
read/write block size of 512 byte blocks, and QIC-320 read/write block size of 1024 byte blocks. With QIC format style tapes all reads and
writes must be in multiple of the block size. This is a requirement of fixed block tape drives because record boundaries are not pre-
served. The QIC densities are selected using the following special device names:
QIC-24 Fixed block size.
QIC-120 Fixed block size.
QIC-150 Fixed block size.
QIC-320 Fixed block size.
With all fixed block tape devices a of a file to the tape must be padded out. An example of this is a of which has a size of approximately
3800 bytes.
dd if=/etc/gettytab of=/dev/rmt0h bs=10k conv=sync
or
dd if=/etc/gettytab of=/dev/rmt0l bs=512 conv=sync
The option of pads the output to block size.
This driver also supports n-buffered reads and writes to the raw tape interface (used with streaming tape drives). See for further
details.
Tape Support
TZ30, TZK50, TLZ04, TSZ05, TKZ08, TZK10
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
Files
See Also
mtio(4), nbuf(4), SCSI(4), MAKEDEV(8), uerf(8), tapex(8)
Guide to the Error Logger
tz(4)