Sponsored Content
Special Forums IP Networking Quad Fast Ethernet Card on Sparc 10? Post 9258 by doeboy on Wednesday 24th of October 2001 04:41:32 PM
Old 10-24-2001
Did you make sure the hostname for each respective interface is contained in each hostname.qex file?

BTW... That is a Quad-Ethernet card. Quad-Fast Ethernet cards are identified as qfe. (Just in case you bought a card thinking it was qfe and not getting 100mbit)
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

4. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

5. Solaris

Quad Ethernet

I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me: SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies

6. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

7. Solaris

quad card configuration

Hi Group, I Have just installed quad card in my V440 machine, I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able, here is details of my machine. ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 ... (2 Replies)
Discussion started by: sameergrover
2 Replies

8. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

9. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies

10. Hardware

Best hardware for a fast local Ethernet?

Dear all, I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card. I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies
HOSTADDR(1)						      General Commands Manual						       HOSTADDR(1)

NAME
hostaddr - show ethernet address, IP address or hostname SYNOPSIS
hostaddr [-eia] [-E eth-device] [-I ip-device] DESCRIPTION
Without any of the -eia options, hostaddr shows the ethernet address, IP address and hostname of the local host on one line in the given order. With options only the wanted fields are shown, still in the same order, not in option order. OPTIONS
-e Show the ethernet address. -i Show the IP address. This will not work if no IP address has been found by RARP or by setting it with ifconfig(8). -a Show the fully qualified hostname. The IP address is shown again if it can't be translated to a host name. (This usually indicates that the DNS reverse address translation tables are incomplete.) SEE ALSO
ifconfig(8), rarpd(8), nonamed(8), set_net_default(8), boot(8). DIAGNOSTICS
"Timeout" Hostaddr timed out trying to get the IP address. This means that the network connection is out of order or that the setup of the machine is bad. AUTHOR
Kees J. Bot (kjb@cs.vu.nl) HOSTADDR(1)
All times are GMT -4. The time now is 07:51 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy