Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Quad Fast Ethernet Card on Sparc 10?
Special Forums IP Networking Quad Fast Ethernet Card on Sparc 10? Post 9258 by doeboy on Wednesday 24th of October 2001 04:41:32 PM
Old 10-24-2001
Did you make sure the hostname for each respective interface is contained in each hostname.qex file?

BTW... That is a Quad-Ethernet card. Quad-Fast Ethernet cards are identified as qfe. (Just in case you bought a card thinking it was qfe and not getting 100mbit)
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

4. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

5. Solaris

Quad Ethernet

I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me: SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies

6. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

7. Solaris

quad card configuration

Hi Group, I Have just installed quad card in my V440 machine, I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able, here is details of my machine. ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 ... (2 Replies)
Discussion started by: sameergrover
2 Replies

8. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

9. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies

10. Hardware

Best hardware for a fast local Ethernet?

Dear all, I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card. I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies

LEARN ABOUT NETBSD

hme

HME(4)							   BSD Kernel Interfaces Manual 						    HME(4)

NAME

     hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver

SYNOPSIS

     hme* at pci? dev ? function ?
     hme* at sbus? slot ? offset ?

DESCRIPTION

     The hme driver supports Sun Microelectronics STP2002-STQ Fast Ethernet interfaces.

HARDWARE

     The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models.

     Cards supported by the hme driver include:

     Sun PCI SunSwift Adapter (``SUNW,hme'')
     Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'')
     Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'')
     Sun SBus Sun100BaseT 2.0 (``SUNW,hme'')
     Sun PCI Quad FastEthernet Controller (``SUNW,qfe'')
     Sun SBus Quad FastEthernet Controller (``SUNW,qfe'')

     The STP2002 family supports hardware checksumming to assist in computing IPv4 TCP/UDP checksums.  The hme driver supports this feature of the
     chip.  See ifconfig(8) for information on how to enable this feature.

SEE ALSO

     ifmedia(4), intro(4), mii(4), ukphy(4), ifconfig(8)

     Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide,
     http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf, April 1996.

HISTORY

     The hme driver first appeared in NetBSD 1.5.

AUTHORS

     The hme driver was written by Paul Kranenburg <pk@NetBSD.org>.

BUGS

     Connecting a MII transceiver on those cards that support it will cause the RJ45 connector to be detected as PHY instance 1, instead of the
     default instance 0.

BSD
								   June 23, 2012							       BSD
All times are GMT -4. The time now is 11:15 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy