Sponsored Content
Top Forums UNIX for Dummies Questions & Answers Configuring networking interface on Sun Blade 1500 Post 91055 by reborg on Tuesday 29th of November 2005 04:34:59 PM
Old 11-29-2005
Since you have no switch or router connetced between the two, you will probably need to force link speed and full/half duplex mode.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Configuring networking interfaces on Solaris 10

Hi, I am trying to configure an ip address, netmask, and default gateway on my solaris machine. For example, in Linux I would do the following command: #ifconfig eth0 xx.xx.xx.xx netmask 255.0.0.0 #add route or route add default xxx.xxx.xxx.xxx In Solaris 10, I believe the commands are... (7 Replies)
Discussion started by: annointed3
7 Replies

2. Solaris

Sun blade 1500 installation and administration problem

Hi I'm completely new in solaris,and don't know many about it. I was installed solaris 10 on sun blade 1500,and also I need to install oracle on it. Now I stuck on some thing and i'm sure that you help me. When i started Oracle installation system told me that I don't have enogh swap space.... (1 Reply)
Discussion started by: dirtyjack
1 Replies

3. Solaris

Configuring interface in zone

Hi All, Please help me in configuring interface in zone I've zone with dedicated interface and I want this interface to get up with global system boot. I am struggling with IP, as always after reboot interface is not getting up automatically and I understand the reason for that.... (10 Replies)
Discussion started by: kumarmani
10 Replies

4. Solaris

Compile PHP 5.3.6 with MySql on Sun Blade 1500 Solaris 10

Hello, I'm trying to compile PHP 5.3.6 with Apache2 and MySql 5.5.12. I hit a problem that I can't seem to resolve by myself and I could not find a solution on the web. It looks like Apache and MySql installed ok, I can start/stop them with no problem. When I try to compile PHP the... (4 Replies)
Discussion started by: pn8830
4 Replies

5. Solaris

Sun Blade 150 not a Sun?

I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05. I have just noticed /bin/sun now returns false, rather than true. See below. $ uname -a SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100 $ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies

6. Solaris

help installing solaris 10 on sun blade 1500

Hi everyone can someone please explain to me how to install solaris 10 on a sunblade 1500 using cdrom? Thanks for your assistance (1 Reply)
Discussion started by: cjashu
1 Replies

7. Solaris

Sun blade 1500 bad magic number

Good afternoon all, First, sorry for my English, this is not my first language but I try my best :). So, here we go. A friend of mine gave me an old Sun Blade 1500 he wasn't using. He said it was working fine except for the missing hard drive. I had in my IT personnal box an old IDE... (33 Replies)
Discussion started by: firstpost
33 Replies

8. UNIX for Dummies Questions & Answers

SUN BLADE T6340 - which OS ?

Hi, I have server SUN BLADE T6340 and i tried install debian sparc on this machine. Will it work ? In the specification is written only Solaris 10. (4 Replies)
Discussion started by: PtaQ
4 Replies

9. UNIX Benchmarks

Blade 1500 Silver

CPU/Speed: UltraSPARC-IIIi/1.5Ghz Ram: 1GB Motherboard: Sparc Bus: PCI Cache: Controller: Disk: ATA Load: 1 user Kernel: SunOS 5.10 Generic_137111-02 Kernel ELF?: yes pgms: gcc 2.95.3 compiled BYTE UNIX Benchmarks (Version 3.11) System -- SunOS aachen95 5.10... (0 Replies)
Discussion started by: MadeInGermany
0 Replies

10. Solaris

Using larger than 120GB drives on a Blade 1500

Hi, I'm using Solaris 8 on a Blade 1500. I know that IDE drives are limited to around 120GB, but I was told that it's possible to use larger drives with the only caveat that the available size will be that 120 (or is it 128?) GB size. But when I try, format shows only very low sizes, like... (2 Replies)
Discussion started by: BobSol8
2 Replies
bscv(7D)							      Devices								  bscv(7D)

NAME
bscv, bscbus, i2bsc - Blade support chip interface driver DESCRIPTION
The bscv, bscbus and i2bsc drivers interface with the Blade support chip used on Sun Microsystem's Blade server products. These drivers provide a conduit for passing control, environmental, cpu signature and event information between Solaris and the Blade support chip. These drivers do not export public interfaces. Instead they make information available via picl, prtdiag, prtfru and related tools. In addition, these drivers log Blade support chip environmental event information into system logs. FILES
/platform/sun4u/kernel/drv/sparcv9/bscbus 64-bit ELF kernel driver /platform/sun4u/kernel/drv/sparcv9/bscv 64-bit ELF kernel driver /platform/sun4u/kernel/drv/sparcv9/i2bsc 64-bit ELF kernel driver /platform/i86pc/kernel/drv/bscbus 32-bit ELF kernel file (x86 only) /platform/i86pc/kernel/drv/bscv 32-bit ELF kernel file (x86 only) ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ |ATTRIBUTE TYPE |ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Architecture |Limited to systems with | | |Blade Support Chip | +-----------------------------+-----------------------------+ |Availability |SUNWcar.u, SUNWcar.i | +-----------------------------+-----------------------------+ SunOS 5.10 22 August 2003 bscv(7D)
All times are GMT -4. The time now is 07:06 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy