11-29-2005
Configuring networking interface on Sun Blade 1500
Hi,
I am attempting to configure my ethernet interface on a Sun Blade 1500. I am testing out my network interface my connecting a crossover cable from my blade to a windows box. I would like to assign an ip address of 10.0.0.2 to "bge0" and netmask of "255.0.0.0". I have typed the following:
# ifconfig bge0 plumb
#ifconfig bge0 10.0.0.2 netmask 255.0.0.0
#ifconfig bge0 up
# ping 10.0.0.3 (ip address of windows machine)
No answer from 10.0.0.3
Why is my network interface not configured properly? I know on my windows box that I have 10.0.0.1 defined as the default gateway. Is this necessary also on my Sun Blade? If so, what is the syntax for creating a default gateway with that ip address?
I tried the following:
#route add default gateway 10.0.0.1
but when trying to ping windows box, I still did not get any answer
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I am trying to configure an ip address, netmask, and default gateway on my solaris machine. For example, in Linux I would do the following command:
#ifconfig eth0 xx.xx.xx.xx netmask 255.0.0.0
#add route or route add default xxx.xxx.xxx.xxx
In Solaris 10, I believe the commands are... (7 Replies)
Discussion started by: annointed3
7 Replies
2. Solaris
Hi
I'm completely new in solaris,and don't know many about it.
I was installed solaris 10 on sun blade 1500,and also I need to install oracle on it.
Now I stuck on some thing and i'm sure that you help me.
When i started Oracle installation system told me that I don't have enogh swap space.... (1 Reply)
Discussion started by: dirtyjack
1 Replies
3. Solaris
Hi All,
Please help me in configuring interface in zone
I've zone with dedicated interface and I want this interface to get up with global system boot. I am struggling with IP, as always after reboot interface is not getting up automatically and I understand the reason for that.... (10 Replies)
Discussion started by: kumarmani
10 Replies
4. Solaris
Hello,
I'm trying to compile PHP 5.3.6 with Apache2 and MySql 5.5.12. I hit a problem that I can't seem to resolve by myself and I could not find a solution on the web.
It looks like Apache and MySql installed ok, I can start/stop them with no problem.
When I try to compile PHP the... (4 Replies)
Discussion started by: pn8830
4 Replies
5. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
6. Solaris
Hi everyone
can someone please explain to me how to install solaris 10 on a sunblade 1500 using cdrom?
Thanks for your assistance (1 Reply)
Discussion started by: cjashu
1 Replies
7. Solaris
Good afternoon all,
First, sorry for my English, this is not my first language but I try my best :).
So, here we go.
A friend of mine gave me an old Sun Blade 1500 he wasn't using. He said it was working fine except for the missing hard drive.
I had in my IT personnal box an old IDE... (33 Replies)
Discussion started by: firstpost
33 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I have server SUN BLADE T6340 and i tried install debian sparc on this machine.
Will it work ?
In the specification is written only Solaris 10. (4 Replies)
Discussion started by: PtaQ
4 Replies
9. UNIX Benchmarks
CPU/Speed: UltraSPARC-IIIi/1.5Ghz
Ram: 1GB
Motherboard: Sparc
Bus: PCI
Cache:
Controller:
Disk: ATA
Load: 1 user
Kernel: SunOS 5.10 Generic_137111-02
Kernel ELF?: yes
pgms: gcc 2.95.3 compiled
BYTE UNIX Benchmarks (Version 3.11)
System -- SunOS aachen95 5.10... (0 Replies)
Discussion started by: MadeInGermany
0 Replies
10. Solaris
Hi,
I'm using Solaris 8 on a Blade 1500.
I know that IDE drives are limited to around 120GB, but I was told that it's possible to use larger drives with the only caveat that the available size will be that 120 (or is it 128?) GB size.
But when I try, format shows only very low sizes, like... (2 Replies)
Discussion started by: BobSol8
2 Replies
LEARN ABOUT DEBIAN
vde_l3
VDE_L3(1) General Commands Manual VDE_L3(1)
NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch.
SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket]
DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup
for each -v option given at command line. Static routes to target networks can be defined using the -r option.
vde_l3 -v /var/run/s1.ctl:192.168.0.1/24
connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0.
vde_l3
-v /var/run/s1.ctl:192.168.0.1/24
-v /var/run/s2.ctl:10.0.0.254/255.255.0.0
connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in
each network can specify the vde_l3 as their gateway to reach the other one.
OPTIONS
-v vde_plug:ipaddress/netmask
Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can
be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One
can define as many interfaces as she wants.
-r target_network/netmask:gateway
Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she
wants.
-G default_gw
Specify a default gateway, to be used whenever no static route is defined for a target host.
-M mgmt_socket
the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be
used as a remote terminal for wirefilter.
NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik"
i.e. the German "Association for Electrical, Electronic & Information Technologies").
SEE ALSO
vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1).
AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net>
VDE is a project by Renzo Davoli <renzo@cs.unibo.it>
Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)