11-20-2005
boot problems
i have 2 server es40 and ds20 with with unix truevector , the es40 is down cause of hard problem
i have traied to take hard disksfrom ES40 and put then in DS20
but there is problem
-------------------------------------------------------------------------------------------------------------
loading vmunix symbol table<<
trap : invalide memory read access <<
from kernel mode<<
faulting virtual address 0x000000000000<<
pc of faulting instruction 0xfffffc000058b30<<
...................................................... ra <<
...................................................... sp <<
panic (cpu):kernel memory fault
dump no primary swap,noexplicite dump dev. nowhere to put header,giving up
cp - save_term routine table to be called
cp - save_term exited within
halt int
pc = fffffc000056bb70
please i neeeeeeeeeeeeeeeeeeeeeeeed help
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
i have windows 2000 on hda. when i was running freebsd on hdb, i installed their boot manager and it worked fine.
today i installed suse linux on hdb in place of freebsd, but the freebsd boot manager is still there. it will boot windows but has some problems trying to boot linux. the boot... (1 Reply)
Discussion started by: nydel
1 Replies
2. UNIX for Dummies Questions & Answers
Hi Everyone,
I have a problem. I'm trying too reinstall sun solaris 8.0 on may Sunfire 280r but solaris 9.0 is all ready installed. I tried to boot from cd rom it keeps telling me that File does not seem executable. I need to get Solaris 8.0 on this system. I have boot all ready in single mode... (4 Replies)
Discussion started by: Peterh
4 Replies
3. UNIX for Dummies Questions & Answers
During the boot process of my SPARCstation 5, it hangs up at this message: Setting default interface for multicast: add net 224.0.0.0: gateway jpt2. What do I need to do to get past this point? Is there something I need to turn off? (2 Replies)
Discussion started by: saucierm
2 Replies
4. UNIX for Dummies Questions & Answers
Hi!
I got some serious problems with booting the computer. When started it prints GRUB GRUB GRUB all over the screen. tchan on #grub tried to help me but with no result. Here is the log.
Mabey there is something that we have missed?:confused: (3 Replies)
Discussion started by: Barfly.se
3 Replies
5. Debian
Hello, I recently installed Knoppix 4.0.2 on my PC there is dual boot with W2K,
the installation runs without a problem, but everytime that I boot appears this message:
Kernel panic-not syncing:VFS:unable to munt root fs on unknow block (3,6)
Can anybody help me to know, waht is happenning?... (6 Replies)
Discussion started by: GEIER
6 Replies
6. Solaris
I'm new to Unix so please bear with me.
We had a Ultra 10 running solaris 8 and the motherboard went. So we bought a replacement Ultra 10 on ebay. Exact same hardware. Swapped out the drives with our drives and booted. The new system was set up to boot off disk1 and ours were set to boot off... (1 Reply)
Discussion started by: jbestor
1 Replies
7. AIX
I am trying to install AIX 4.3 on a 44P-170 and am having problems. I have the 44P connected to a laptop through the serial port and am trying to boot from the IBM AIX 4.3 CD and I can only get as far as the SMS (I believe) screen. The current Processor Firmware is sh040616 and the system... (3 Replies)
Discussion started by: SeanU
3 Replies
8. Solaris
Can't seem to get it to boot from cd
boot cd
rebooting with command: boot cd
boot device: /pci@8600000/sunw,qlc@4/fp@0,0/disk@1,0 file and args: cd
boot: cannot open cd
enter filename :
trying to install solaris 9 9/04 just to use it as a simple workstation on home network quite new... (25 Replies)
Discussion started by: solnewbie
25 Replies
9. Solaris
Hi folks, I was trying to setup Network based NFS installation with PXE.
I'm using virtual box for this purpose. I have one redhat (DHCP) server and Solaris 10 (Install server - Source) and on the other one am trying to install solaris using PXE. As in, dhcp address and boot file can be fetched... (2 Replies)
Discussion started by: vijaytrendz
2 Replies
10. Solaris
Hi all,
I've just replaced the eprom battery on my Sun Ultra-30 and having boot issues. For some reason its trying to boot off the network instead of the DISK1. Howe can I change it so the open boot does not default to the boot device: NET
Thanks,
Rob (3 Replies)
Discussion started by: robbo007
3 Replies
LEARN ABOUT V7
arithmetic
ARITHMETIC(6) Games Manual ARITHMETIC(6)
NAME
arithmetic - provide drill in number facts
SYNOPSIS
/usr/games/arithmetic [ +-x/ ] [ range ]
DESCRIPTION
Arithmetic types out simple arithmetic problems, and waits for an answer to be typed in. If the answer is correct, it types back "Right!",
and a new problem. If the answer is wrong, it replies "What?", and waits for another answer. Every twenty problems, it publishes statis-
tics on correctness and the time required to answer.
To quit the program, type an interrupt (delete).
The first optional argument determines the kind of problem to be generated; +-x/ respectively cause addition, subtraction, multiplication,
and division problems to be generated. One or more characters can be given; if more than one is given, the different types of problems
will be mixed in random order; default is +-
Range is a decimal number; all addends, subtrahends, differences, multiplicands, divisors, and quotients will be less than or equal to the
value of range. Default range is 10.
At the start, all numbers less than or equal to range are equally likely to appear. If the respondent makes a mistake, the numbers in the
problem which was missed become more likely to reappear.
As a matter of educational philosophy, the program will not give correct answers, since the learner should, in principle, be able to calcu-
late them. Thus the program is intended to provide drill for someone just past the first learning stage, not to teach number facts de
novo. For almost all users, the relevant statistic should be time per problem, not percent correct.
ARITHMETIC(6)