10-27-2005
Your OS has files which are excuted when the system boots. You must put systems instructions, like your routing information, in those system boot files.
See this IBM info for AIX boot files.
9 More Discussions You Might Find Interesting
1. Solaris
How do I make a route permanent, other than default route on a Solaris server? (1 Reply)
Discussion started by: jontom
1 Replies
2. AIX
Hi,
After accidental default route removal serial connection doesn't work.
What should I do to connect to my machine ?
thanks
Vilius (7 Replies)
Discussion started by: vilius
7 Replies
3. Solaris
Hi,
I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies
4. Solaris
how do I make sure that the entry in the routing table on Solaris 8 stay permanent after rebooting the server.
For example
route add 172.20.1.60 -netmask 255.255.255.0 172.20.255.253
Each time the server reboots the entry disappears when using the command netstat -nr (2 Replies)
Discussion started by: tv.praveenkumar
2 Replies
5. AIX
Hello I have a question regarding default route on AIX servers. (I am using a p5 5.3 TL9 machine).
in my output of "lsattr -El inet0" I can see there are two routes like below.
route net,-hopcount,0,,0,x.x.207.7 Route True
route net,-hopcount,0,,0,x.x.202.129 Route True
But... (9 Replies)
Discussion started by: gsabarinath
9 Replies
6. Solaris
Hiya,
I got the default gateway set in /etc/defaultrouter file, however "netstat -nr" doesn't show anything like "default" in the routing table. As far as I know "netstat" on Solaris 10 u7 should show something like :
Routing Table: IPv4
Destination Gateway Flags Ref ... (8 Replies)
Discussion started by: TomSu
8 Replies
7. IP Networking
Greetings,
I am using debian squeeze to perform the following operation:
1. pxeboot Alix 2.c board into debian installer
When I get to the installer my laptop's dhcp server successfully provides an ip address but does not set up the default route. I am not sure how to provide this.
I... (2 Replies)
Discussion started by: mock
2 Replies
8. AIX
AIX version 5.3
when I try to add default gateway
# route add 0 192.168.100.254
Or
# route add default 192.168.100.254
I get the error
0821-275 route: socket: The file access permissions do not allow the specified action.
searching on google i came across similar... (5 Replies)
Discussion started by: filosophizer
5 Replies
9. Solaris
Hi All
Recently we have faced issue in SUN server
after reboot of node 2 default routs has been added to system as below
IRE Table: IPv4
**Destination*************Mask***********Gateway**********Device Mxfrg Rtt***Ref Flg**Out**In/Fwd*
-------------------- ---------------... (2 Replies)
Discussion started by: aaysa123
2 Replies
LEARN ABOUT OPENDARWIN
installgrub
installgrub(1M) installgrub(1M)
NAME
installgrub - install GRUB in a disk partition or a floppy
SYNOPSIS
/sbin/installgrub [-fm] stage1 stage2 raw-device
The installgrub command is an -only program. GRUB stands for GRand Unified Bootloader.
installgrub installs GRUB stage 1 and stage 2 files on the boot area of a disk partition. If you specify the -m option, installgrub
installs the stage 1 file on the master boot sector of the disk.
The installgrub command accepts the following options:
-f
Suppresses interaction when overwriting the master boot sector.
-m
Installs GRUB stage1 on the master boot sector interactively.
The installgrub command accepts the following operands:
stage1
The name of the GRUB stage 1 file.
stage2
The name of the GRUB stage 2 file.
raw-device
The name of the device onto which GRUB code is to be installed. It must be a character device that is readable and writable. For disk
devices, specify the slice where the GRUB menu file is located. (For Solaris it is the root slice.) For a floppy disk, it is
/dev/rdiskette.
Example 1: Installing GRUB on a Hard Disk Slice
The following command installs GRUB on a system where the root slice is c0d0s0:
example# /sbin/installgrub /boot/grub/stage1
/boot/grub/stage2 /dev/rdsk/c0d0s0
Example 2: Installing GRUB on a Floppy
The following command installs GRUB on a formatted floppy:
example# mount -F pcfs /dev/diskette /mnt
# mkdir -p /mnt/boot/grub
# cp /boot/grub/* /mnt/boot/grub
# umount /mnt
# cd /boot/grub
# /sbin/installgrub stage1 stage2 /dev/rdiskette
/boot/grub
Directory where GRUB files reside.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
boot(1M), fdisk(1M), fmthard(1M), kernel(1M), attributes(5)
Installing GRUB on the master boot sector (-m option) overrides any boot manager currently installed on the machine. The system will always
boot the GRUB in the Solaris partition regardless of which fdisk partition is active.
24 May 2005 installgrub(1M)