10-08-2005
Finally!! Sparcbook keyboard works, but X-server still not working..to get laptop keyboard working in run level 3 did:
1. boot cdrom -s
2. mount /dev/dsk/c0t0d0s0 /mnt
3. cd /mnt/etc
4. chmod 744 dacf.conf
5. cp dacf.conf dacf.conf.ORIG
6. cat >>dacf.conf
7. Enter two lines mentioned above (e.g. "driver-minorname="kb8042 ..etc") then exit using CTRL-D
8. cd /
9. umount /mnt
10. reboot
Now can any-1 help with getting X-server working :-)
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've been given access to a virtual server. I've worked out how to connect with it using SSH (in my unix terminal window). But I'm clueless about how to continue. The last time I made web services. I had a fancy web-based control panel. Now I just have the command line.
There are three... (1 Reply)
Discussion started by: knownothing
1 Replies
2. Solaris
Hi,
I have Solaris 9 installed on a SunFire V880. When the machine boots up, I get a message, "the X-server cannot be started on display:0".
I searched the forum for possible solution, however, they are not applicable to my problem for two reasons: either the platform is different or the... (6 Replies)
Discussion started by: purveshkhatri
6 Replies
3. Solaris
Iam using a Dell laptop..... i installed Solaris 10.... 'm getting a X-Server cannot be started on display 0 error. Can anyone help me in fixing ??? (2 Replies)
Discussion started by: sarathnag25
2 Replies
4. Solaris
Are rc scripts executed serially or all at the same time. Is there a way to see this happen? A log file or the syslogd?
This is Solaris 10. (2 Replies)
Discussion started by: djehresmann
2 Replies
5. Solaris
Hey Guys,
I have just moved my machine to a new location
and reconfigured my DNS and ip...
and for an unknown reason
I get this X-Server can not be started error on startup.
This is what I got in my Xerrors log:
It is possible to start a graphical session (X-Server) manually, ... (8 Replies)
Discussion started by: wasabihowdi
8 Replies
6. Solaris
hi ,
I have install Oracle solaris 10 8/11 on intel core i5 server. But its not opening in graphic mode showing message X-Server can not be started on display ...
(EE) Unable to locate/open config file
Drivers to try are: "intel" "i810" "fbdev" "vesa" vga"
(EE) failed to load module "dri"... (3 Replies)
Discussion started by: zeeshan047
3 Replies
7. Red Hat
Hi Friends,
My Server is con't stated..it shows the below error..
Red hat exterprise Linux As Release 4(nahat)
kernel 2.6.9-5.ELsmp on an i686
INIT : id "x" respawing too fast :disabled for 5 minutes...
Please help help
Thanks,
Srinivas (1 Reply)
Discussion started by: srinivas814
1 Replies
8. Red Hat
Dear Expert Users,
VMware Admin Tool is used to create a "clone" of an existing VM RHEL Server. Now, I have a Project where a cloned VM Server image is started for run . Please share what are all configuration changes required to ensure this runs fine ?
I will be grateful for quick and... (2 Replies)
Discussion started by: schandrakar1
2 Replies
9. UNIX for Beginners Questions & Answers
This question is more in the line of how init messages get sent to a console during startup/shutdown. My problem has to do with exporting a VM from AWS to KVM (and a retry on virtual box). I am looking for a understanding on how init messages are sent to a device and what controls them My two... (0 Replies)
Discussion started by: jtkells
0 Replies
10. UNIX for Beginners Questions & Answers
Good Morning,
I recently cloned a sunblade 2500 to another sunblade 2500 and had an issue getting the GUI: X-Server can not be started on display :0
The issue was that the first machine had an xvr600 graphics card, and the new machine had an xvr100. Installing a new driver took... (0 Replies)
Discussion started by: Stellaman1977
0 Replies
LEARN ABOUT FREEBSD
mqueuefs
MQUEUEFS(5) BSD File Formats Manual MQUEUEFS(5)
NAME
mqueuefs -- POSIX message queue file system
SYNOPSIS
To link into kernel:
options P1003_1B_MQUEUE
To load as a kernel loadable module:
kldload mqueuefs
DESCRIPTION
The mqueuefs module will permit the FreeBSD kernel to support POSIX message queue. The module contains system calls to manipulate POSIX mes-
sage queues. It also contains a file system to implement a view for all message queues of the system. This helps users to keep track of
their message queues and make it more easily usable without having to invent additional tools.
The most common usage is as follows:
mount -t mqueuefs null /mnt/mqueue
where /mnt/mqueue is a mount point.
It is possible to define an entry in /etc/fstab that looks similar to:
null /mnt/mqueue mqueuefs rw 0 0
This will mount mqueuefs at the /mnt/mqueue mount point during system boot. Using /mnt/mqueue as a permanent mount point is not advised as
its intention has always been to be a temporary mount point. See hier(7) for more information on FreeBSD directory layout.
Some common tools can be used on the file system, e.g.: cat(1), chmod(1), chown(8), ls(1), rm(1), etc. To use only the message queue system
calls, it is not necessary for user to mount the file system, just load the module or compile it into the kernel. Manually creating a file,
for example, ``touch /mnt/mqueue/myqueue'', will create a message queue named myqueue in the kernel, default message queue attributes will be
applied to the queue. It is not advised to use this method to create a queue; it is better to use the mq_open(2) system call to create a
queue as it allows the user to specify different attributes.
To see the queue's attributes, just read the file:
cat /mnt/mqueue/myqueue
SEE ALSO
mq_open(2), nmount(2), unmount(2), mount(8), umount(8)
AUTHORS
This manual page was written by David Xu <davidxu@FreeBSD.org>.
BSD
November 30, 2005 BSD