SCO Unixware 7.1.1
Hi friends,
At 11:30pm last night mymain Unix Server hung or rebooted (Unaware which one), and was bot available for 10 minutes. Is there a log file somewhere which will tell me what happened ?
I have looked ad /var/adm/syslog, but cannot make head nor tail of it.
... (1 Reply)
Virtually no UNIX admin experience. Any admin duties are shared by several folks with no special training. Today we had our Sun v880 server, running Solaris 5.8, shutdown for no apparent reason.
When we checked on server we found it completely powered down, yet still connected to a fully... (6 Replies)
Dear all,
My server has shutdown frequently.
It is AMD64, OS is RHEL 4 U5.
I've seen the system log, before the shutdown occured:
Jul 29 04:28:56 localhost kernel: EDAC k8 MC0: general bus error: participating processor(local node response), time-out(no timeout) memory transaction... (2 Replies)
Hi,
please could someone advise the best command to shutdown and then for it to reboot back online again.
Note: I shall be doing this from a telent session.
regards
venhart (3 Replies)
I have a sparc T1 server (I know its old) running Solaris 8, which we use for testing. It has been very slow in response- prompt takes couple of minutes to come up, so I decided to reboot the server but I can reboot it, it is giving following errors when I try to shutdown it down.
root@deva:/#... (3 Replies)
Are rc scripts executed serially or all at the same time. Is there a way to see this happen? A log file or the syslogd?
This is Solaris 10. (2 Replies)
Hi All,
I want to shutdown the server if no one is actualy using it. Its a linux server.
I thought of sending a msg on users terminal for those who all are logged in and expecting a input from them.
If they will reply system should not get shutdown else it should not.
Can any one... (2 Replies)
Hi,
is it possible to find out ip address of user who has shutdown or rebooted the server , I have used the command errpt -a , in that it is showing server rebooted but it is not showing ip address who has shutdown the serve, even I have used command last reboot.
Please suggest.
Regards,
... (3 Replies)
Working with a T5240/Solaris 10 and trying to figure out if there is a setting that will automatically shutdown the server if it hits a certain temperature. I'm just trying to identify if there is a setting in place and what that temperature is...
Any help is much appreciated! (5 Replies)
Discussion started by: ojgraham
5 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)