10-11-2001
hi optimus
thks for suggestions .. is it behaving due to the mismatch in the driver or due to any other reason??..
Regds
Francis
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. UNIX for Advanced & Expert Users
HI,
I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors
genunix: NOTICE: glm0: fault detected in device; service still unavailable
genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported.
Anyone has an idea, how to resolve... (1 Reply)
Discussion started by: s_aamir
1 Replies
4. SCO
Dear all
Im facing one problem in SCO 5.0.5 , its that in the server there are three LAN cards INTEL PRO 100 series but when we configure all the three cards then LAN stops working . self ping is possible but no one can ping the server. If we remove driver of any one card LAN starts working.
Is... (1 Reply)
Discussion started by: ccvyas
1 Replies
5. Solaris
Hello,
I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9).
Who have already done this and can give me the procedure to follow ?
driver to install
multipath
etc...
Thanks in advance
Emmanuel (1 Reply)
Discussion started by: emma32
1 Replies
6. Solaris
Hi all,
i have configured my solaris 5 .10 for internet connection by editing the files /etc/hosts/,/etc/resolve.config,/etc/defalutrouter and nsswitchconfig .
during installation i was not requested for ip adddress even i plugged network cable.
am i need to install any network card... (2 Replies)
Discussion started by: srikanthg
2 Replies
7. Solaris
I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance. (12 Replies)
Discussion started by: mokkan
12 Replies
8. Solaris
All,
I have a unique situation concerning RSC cards and would like to see if anyone has a solution. Here is the situation:
We are migrating older versions of Solaris using ufsdump images to like older hardware. We basically installed a temporary Solaris O/S then copied the dumps over and... (5 Replies)
Discussion started by: sljack
5 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Solaris
Hello all,
I am trying to learn about Solaris and Sun systems so I purchased a SunFire 280r running Solaris 9 with a disk array from eBay. The system had no video card so I purchased a PGX32 card for the PCI slot and installed it.
The problem is I have no video what so ever. I am familiar... (3 Replies)
Discussion started by: FTBTX
3 Replies
HFA(4) BSD Kernel Interfaces Manual HFA(4)
NAME
hfa -- FORE Systems 200-Series ATM adapter driver
SYNOPSIS
device hfa
DESCRIPTION
The hfa driver provides support for the FORE Systems ATM series 200 adapters. This driver will support up to eight devices in a system at
any given time. The hfa driver follows the AALI or FORE ATM Adaptation Layer Interface and as such will adhere to its specifications. The
supported AALs include:
o FORE AAL 0: The cell service;
o FORE AAL 4: Version three and four of AAL;
o FORE AAL 5: Version five of AAL.
The hfa driver supports traffic shaping for cards with firmware revisions of 4.X.X, see fore_dnld(8). The following sysctls are recognized
by the driver and may be used to enable or disable traffic shaping:
hw.atm.hfaN.shape (0)
Disable shaping on card number N.
hw.atm.hfaN.shape (1)
Set one VCI to be traffic shaped on device N. This will shape the first CBR VCI which is opened.
hw.atm.hfaN.shape (2)
Attempt to shape all VCIs on device N.
The firmware should be loaded before using this driver, this can be an easy task if the fore_dnld(8) utility is used. If the /etc/rc.d/atm1
file has been properly configured then the firmware update should be automatic.
HARDWARE
The hfa driver supports the following adapters:
o FORE Systems PCA-200E ATM
o FORE Systems 200S
o FORE Systems 200
DIAGNOSTICS
fore_cmd_drain: %s%d: GET_PROM failed The driver failed to drain the PROM buffer.
fore initialization failed: intf=%s%d Initialization of the card has failed.
fore initialization timed out: intf=%s%d Initialization of the card has timed out.
hfa: version mismatch: fore=%d.%d kernel=%d.%d A version mismatch error has occurred.
SEE ALSO
fatm(4), harp(4), ng_atm(4), atm(8), fore_dnld(8)
HISTORY
The hfa driver was written by Network Computing Services, Inc. and added to FreeBSD 3.0 by Poul-Henning Kamp <phk@FreeBSD.org>. This manual
page first appeared in FreeBSD 5.3.
AUTHORS
This manual page was written by Tom Rhodes <trhodes@FreeBSD.org>.
BSD
August 6, 2004 BSD