10-10-2001
Problem with N/W card in solaris
hi all
We went to analyze a intel based server installed with Solaris 8 .previuosly on that machine Rhat 7.1 was loaded and working fine in the N/W. After we loaded Solaris 8 it got automatically rebooted when it comes to the Gui mode.The same happened thirce and we opted out to load without network support then the process went down smoothly .Then we configured the machine once again in the N/W but the same thing is still continuing i.e restarting everytime if a telnet session is opened or automatically after sometime.We came to know that it has taken the N/W card driver as Intel pro 100/B but the N/W card in our machine is Pro 100+ . we tried for the drivers on both intel and sun site.Can anybody help us in this problem ??we want to confirm is it the problem due to the Driver only ??
Thanks for help
Francis
Last edited by edwin_francis; 10-10-2001 at 05:07 AM..
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. UNIX for Advanced & Expert Users
HI,
I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors
genunix: NOTICE: glm0: fault detected in device; service still unavailable
genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported.
Anyone has an idea, how to resolve... (1 Reply)
Discussion started by: s_aamir
1 Replies
4. SCO
Dear all
Im facing one problem in SCO 5.0.5 , its that in the server there are three LAN cards INTEL PRO 100 series but when we configure all the three cards then LAN stops working . self ping is possible but no one can ping the server. If we remove driver of any one card LAN starts working.
Is... (1 Reply)
Discussion started by: ccvyas
1 Replies
5. Solaris
Hello,
I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9).
Who have already done this and can give me the procedure to follow ?
driver to install
multipath
etc...
Thanks in advance
Emmanuel (1 Reply)
Discussion started by: emma32
1 Replies
6. Solaris
Hi all,
i have configured my solaris 5 .10 for internet connection by editing the files /etc/hosts/,/etc/resolve.config,/etc/defalutrouter and nsswitchconfig .
during installation i was not requested for ip adddress even i plugged network cable.
am i need to install any network card... (2 Replies)
Discussion started by: srikanthg
2 Replies
7. Solaris
I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance. (12 Replies)
Discussion started by: mokkan
12 Replies
8. Solaris
All,
I have a unique situation concerning RSC cards and would like to see if anyone has a solution. Here is the situation:
We are migrating older versions of Solaris using ufsdump images to like older hardware. We basically installed a temporary Solaris O/S then copied the dumps over and... (5 Replies)
Discussion started by: sljack
5 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Solaris
Hello all,
I am trying to learn about Solaris and Sun systems so I purchased a SunFire 280r running Solaris 9 with a disk array from eBay. The system had no video card so I purchased a PGX32 card for the PCI slot and installed it.
The problem is I have no video what so ever. I am familiar... (3 Replies)
Discussion started by: FTBTX
3 Replies
EX(4) BSD/i386 Kernel Interfaces Manual EX(4)
NAME
ex -- Ethernet device driver for the Intel EtherExpress Pro/10 and Pro/10+
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ex
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_ex_load="YES"
DESCRIPTION
The ex driver provides support for Ethernet adapters based on the Intel i82595 chip.
On the ISA bus, the card will be searched for in the I/O address range 0x200 - 0x3a0. The IRQ will be read from the EEPROM on the card. For
correct operation Plug-N-Play support should be disabled.
On the PC Card bus, the card will be automatically recognized and configured.
HARDWARE
The ex driver supports the following Ethernet adapters:
o Intel EtherExpress Pro/10 ISA
o Intel EtherExpress Pro/10+ ISA
o Olicom OC2220 Ethernet PC Card
o Olicom OC2232 Ethernet/Modem PC Card
o Silicom Ethernet LAN PC Card
o Silicom EtherSerial LAN PC Card
DIAGNOSTICS
ex%d: Intel EtherExpress Pro/10, address %6D, connector %s The device probe found an installed card, and was able to correctly install the
device driver.
ex%d: WARNING: board's EEPROM is configured for IRQ %d, using %d The device probe detected that the board is configured for a different
interrupt than the one specified in the kernel configuration file.
ex%d: invalid IRQ. The device probe detected an invalid IRQ setting.
SEE ALSO
arp(4), netintro(4), ng_ether(4), ifconfig(8)
HISTORY
The ex device driver first appeared in FreeBSD 2.2.
AUTHORS
The ex device driver was written by Javier Martin Rueda. The PC Card attachment was written by Mitsuru ISAWAKI and Warner Losh. This manual
page was written by David E. O'Brien.
BUGS
Currently the driver does not support multicast.
The Silicom EtherSerial card's serial port does not currently work. The Olicom OC2232 PC Card should work with the ex driver, but is cur-
rently completely broken.
BSD
July 16, 2005 BSD