10-01-2001
Installing nic on sco 5.0.5
How do I install an intel nic on sco 5.0.5 it did not detect when i installed the program
10 More Discussions You Might Find Interesting
1. IP Networking
How to install a second (ethernet) NIC on a Sun station on PCI 1?
Thanks! (2 Replies)
Discussion started by: igorgog
2 Replies
2. SCO
Dear Sir,
We are using sco 5.0.6 version. we need to install the informix database standard engine(SE) into this server. Kindly give me detailed instruction of preconfiguration( e.g. path) of sco 5.0.6 server.
Kind Regards,
Mostafizur Rahman (1 Reply)
Discussion started by: rahmanm
1 Replies
3. SCO
Hi guys,
I am a newbie in SCO UNIX, and I am having problem in installing a NIC for my machine:
My machine: UnixWare scou 5 7.1.4 i386 x86at SCO UNIX_SVR5
My NIC is dLink DFE-538TX, I got the driver from:
http://support.dlink.ca/ProductView.asp?ProductModel=DFE-538TX
The driver... (1 Reply)
Discussion started by: Voldi
1 Replies
4. Solaris
After seeing that http://sol-enet.sourceforge.net/support.shtml had drivers for my NIC, I decided to download them on my windows machine so I could burn them to a CD and install them on my old gateway so I could try to get it on the internet. While following the instructions with the drivers, I... (2 Replies)
Discussion started by: xtremepancakez
2 Replies
5. SCO
I have a few resources that I have read that show what I need, openSSL and zlib of one version or another to get openSSH to work to start.
Here is my dilemma to start, I will need to compile the source for the openSS* and the zlib, but when I type "make" into the command prompt I get "make: not... (8 Replies)
Discussion started by: PinkLemonade
8 Replies
6. SCO
Hi am Running SCO UNIXware 7.1.4 am i cant stand the shell that comes with, i downloaded the source for bash and the uncompressed it.
I run the:- ./configure and that went through with no issues
I then ran make that also went through fine with no errors.
But when i ran make install i got... (1 Reply)
Discussion started by: Han.nlo
1 Replies
7. SCO
I have a SCO 5.0.7 server.As there is no parellel port ,printing is done via USB port.
After loading the Network Card driver ,during booting the server gets hanged and the NIC driver is not loaded.If the USB ports are disabled the NIC driver gets loaded.
As both USB and NIC driver are essential... (0 Replies)
Discussion started by: vikramviky
0 Replies
8. SCO
Has anyone installed SCO 6 in Virtualbox? I was quite successful with 5.0.6 but then when I tried SCO 6, it will not report any nic (I am using resmgr to see who is there). The available cards under virtualbox are pcnet-pci II and II, and a few intel/pro 1000s. I have installed the maintenance pack... (1 Reply)
Discussion started by: dalek
1 Replies
9. SCO
How I install sco unix 5.02 on hard disk ide. I have cd-rom scsi (1 Reply)
Discussion started by: Terence
1 Replies
10. SCO
Hi
I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question:
PCI BUS#
DEVICE#... (3 Replies)
Discussion started by: TinhNhi
3 Replies
LEARN ABOUT CENTOS
debuginfo-install
debuginfo-install(1) debuginfo-install(1)
NAME
debuginfo-install - install debuginfo packages and their dependencies
SYNOPSIS
debuginfo-install package
DESCRIPTION
debuginfo-install is a program which installs the RPMs needed to debug the specified package. The package argument can be a wildcard, but
will only match installed packages. debuginfo-install will then enable any debuginfo repositories, and install the relevant debuginfo rpm.
EXAMPLES
Download and install all the RPMs needed to debug the kernel RPM:
debuginfo-install kernel
WARNING MESSAGES
Could not find debuginfo for:
You may sometimes see warning messages about certain packages not being found if you run debuginfo-install for a wildcard or glob.
Debuginfo packages are not necessary for "noarch" RPMs; these will generate a warning message. Additionally, On 64-bit systems, no
multilib debuginfo packages are published, so if you have 32-bit packages installed, these will also generate warning messages.
FILES
As debuginfo-install uses YUM libraries for retrieving all the information, it relies on YUM configuration for its default values like
which repositories to use. Consult YUM documentation for details:
/etc/yum.conf
/etc/yum/repos.d/
/var/cache/yum/
SEE ALSO
yum.conf (5)
http://yum-utils.baseurl.org/
http://yum.baseurl.org/
AUTHORS
See the Authors file included with this program.
BUGS
There are of course no bugs, but should you find any, you should first consult the FAQ section on http://yum.baseurl.org/wiki/Faq and if
unsuccessful in finding a resolution contact the mailing list: yum-devel@lists.baseurl.org. To file a bug use http://bugzilla.redhat.com
for Fedora/RHEL/Centos related bugs and http://yum.baseurl.org/report for all other bugs.
James Antill 21 October 2008 debuginfo-install(1)