Installing nic on sco 5.0.5 Post: 7754

10 More Discussions You Might Find Interesting

1. IP Networking

Installing second NIC on a Sun!

How to install a second (ethernet) NIC on a Sun station on PCI 1? Thanks!

2. SCO

Installing informix SE at sco 5.0.6

Dear Sir, We are using sco 5.0.6 version. we need to install the informix database standard engine(SE) into this server. Kindly give me detailed instruction of preconfiguration( e.g. path) of sco 5.0.6 server. Kind Regards, Mostafizur Rahman

3. SCO

Need Help installing NIC

Hi guys, I am a newbie in SCO UNIX, and I am having problem in installing a NIC for my machine: My machine: UnixWare scou 5 7.1.4 i386 x86at SCO UNIX_SVR5 My NIC is dLink DFE-538TX, I got the driver from: http://support.dlink.ca/ProductView.asp?ProductModel=DFE-538TX The driver...

4. Solaris

Error while installing NIC drivers

After seeing that http://sol-enet.sourceforge.net/support.shtml had drivers for my NIC, I decided to download them on my windows machine so I could burn them to a CD and install them on my old gateway so I could try to get it on the internet. While following the instructions with the drivers, I...

5. SCO

Installing and using openSSH on SCO 5.0.6

I have a few resources that I have read that show what I need, openSSL and zlib of one version or another to get openSSH to work to start. Here is my dilemma to start, I will need to compile the source for the openSS* and the zlib, but when I type "make" into the command prompt I get "make: not...

6. SCO

Need help installing Bash in SCO

Hi am Running SCO UNIXware 7.1.4 am i cant stand the shell that comes with, i downloaded the source for bash and the uncompressed it. I run the:- ./configure and that went through with no issues I then ran make that also went through fine with no errors. But when i ran make install i got...

7. SCO

IRQ conflict between USB and NIC SCO 5.0.7

I have a SCO 5.0.7 server.As there is no parellel port ,printing is done via USB port. After loading the Network Card driver ,during booting the server gets hanged and the NIC driver is not loaded.If the USB ports are disabled the NIC driver gets loaded. As both USB and NIC driver are essential...

8. SCO

SCO 6 + Virtualbox 2 == no NIC

Has anyone installed SCO 6 in Virtualbox? I was quite successful with 5.0.6 but then when I tried SCO 6, it will not report any nic (I am using resmgr to see who is there). The available cards under virtualbox are pcnet-pci II and II, and a few intel/pro 1000s. I have installed the maintenance pack...

9. SCO

Installing sco unix

How I install sco unix 5.02 on hard disk ide. I have cd-rom scsi

10. SCO

Install NIC on SCO openserver 5.0.2

Hi I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question: PCI BUS# DEVICE#...

LEARN ABOUT SUSE

ocf_heartbeat_viparip

OCF_HEARTBEAT_VIPARI(7) 					OCF resource agents					   OCF_HEARTBEAT_VIPARI(7)

NAME

       ocf_heartbeat_VIPArip - Manages a virtual IP address through RIP2

SYNOPSIS

       VIPArip [start | stop | monitor | validate-all | meta-data]

DESCRIPTION

       Virtual IP Address by RIP2 protocol. This script manages IP alias in different subnet with quagga/ripd. It can add an IP alias, or remove
       one.

SUPPORTED PARAMETERS

       ip
	   The IPv4 address in different subnet, for example "192.168.1.1". (required, string, no default)

       nic
	   The nic for broadcast the route information. The ripd uses this nic to broadcast the route informaton to others (optional, string,
	   default eth0)

       zebra_binary
	   Absolute path to the zebra binary. (optional, string, default /usr/sbin/zebra)

       ripd_binary
	   Absolute path to the ripd binary. (optional, string, default /usr/sbin/ripd)

SUPPORTED ACTIONS

       This resource agent supports the following actions (operations):

       start
	   Starts the resource. Suggested minimum timeout: 20s.

       stop
	   Stops the resource. Suggested minimum timeout: 20s.

       monitor
	   Performs a detailed status check. Suggested minimum timeout: 20s. Suggested interval: 5s.

       validate-all
	   Performs a validation of the resource configuration. Suggested minimum timeout: 20s.

       meta-data
	   Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5s.

EXAMPLE

       The following is an example configuration for a VIPArip resource using the crm(8) shell:

	   primitive example_VIPArip ocf:heartbeat:VIPArip 
	     params 
	       ip=string 
	     op monitor depth="0" timeout="20s" interval="5s"

SEE ALSO

       http://www.linux-ha.org/wiki/VIPArip_(resource_agent)

AUTHOR

       Linux-HA contributors (see the resource agent source for information about individual authors)

resource-agents 1.0.3						    07/05/2010						   OCF_HEARTBEAT_VIPARI(7)

10 More Discussions You Might Find Interesting

1. IP Networking

Installing second NIC on a Sun!

Discussion started by: igorgog

2. SCO

Installing informix SE at sco 5.0.6

Discussion started by: rahmanm

3. SCO

Need Help installing NIC

Discussion started by: Voldi

4. Solaris

Error while installing NIC drivers

Discussion started by: xtremepancakez