07-06-2005
Im not familiar with SCO, but ussually the file being loaded in linux is in the /etc/rc.d/init.d, in FBSD in /etc/, /usr/local/etc/rc.d/, in that directory the script will automaticly read and execute the script. maybe you should read the manual of SCO.
As far as i know, if you create rc.local in /etc, that script will automatic execute after system booting.
CMIIW
Last edited by cleks; 07-06-2005 at 12:26 AM..
10 More Discussions You Might Find Interesting
1. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
2. HP-UX
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies
3. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
4. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
5. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
6. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
7. Solaris
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
6 Replies
8. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
9. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
10. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
LEARN ABOUT SUNOS
systemd-rc-local-generator
SYSTEMD-RC-LOCAL-GENERATOR(8) systemd-rc-local-generator SYSTEMD-RC-LOCAL-GENERATOR(8)
NAME
systemd-rc-local-generator - Compatibility generator for starting /etc/rc.local and /usr/sbin/halt.local during boot and shutdown
SYNOPSIS
/lib/systemd/system-generators/systemd-rc-local-generator
DESCRIPTION
systemd-rc-local-generator is a generator that checks whether /etc/rc.local exists and is executable, and if it is pulls the
rc-local.service unit into the boot process. This unit is responsible for running this script during late boot. Note that the script will
be run with slightly different semantics than the original System V version, which was run "last" in the boot process, which is a concept
that does not translate to systemd. The script is run after network.target, but in parallel with most other regular system services.
systemd-rc-local-generator also checks whether /usr/sbin/halt.local exists and is executable, and if it is pulls the halt-local.service
unit into the shutdown process. This unit is responsible for running this script during later shutdown.
Support for both /etc/rc.local and /usr/sbin/halt.local is provided for compatibility with specific System V systems only. However, it is
strongly recommended to avoid making use of these scripts today, and instead provide proper unit files with appropriate dependencies for
any scripts to run during the boot or shutdown processes.
systemd-rc-local-generator implements systemd.generator(7).
SEE ALSO
systemd(1), systemctl(1)
systemd 237 SYSTEMD-RC-LOCAL-GENERATOR(8)