Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Do I need to add a route??
Special Forums IP Networking Do I need to add a route?? Post 77207 by cleks on Tuesday 5th of July 2005 11:15:37 PM
Old 07-06-2005
Im not familiar with SCO, but ussually the file being loaded in linux is in the /etc/rc.d/init.d, in FBSD in /etc/, /usr/local/etc/rc.d/, in that directory the script will automaticly read and execute the script. maybe you should read the manual of SCO.

As far as i know, if you create rc.local in /etc, that script will automatic execute after system booting.

CMIIW
Last edited by cleks; 07-06-2005 at 12:26 AM..
 

10 More Discussions You Might Find Interesting

1. AIX

route add

Hello , We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ... #route add server.ip router.ip after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies

2. HP-UX

Add Route on HP-UX v10.x, help.

Hi, My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13 I tried with: #route add 192.168.80.2 255.255.255.255 10.10.10.13 but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies

3. IP Networking

Route add probleme

I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system. The ip i am trying to get to is 172.16.4.48 I need to get to it via the hme1 interface. The vpn gateway has this ip 172.30.50.1 I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies

4. Solaris

Route Add

Hi, I am trying to add route command in Solaris 10 machine in the following fashion: route add -host 10.8.112.10 180.144.1.250 -interface lo0:1 this command fails with an error "lo0:1: bad value" I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies

5. IP Networking

route add

I have built a new linux server, via a iLo connection. and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty. Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies

6. Solaris

route add : network is unreachable

Hey Guys: I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1 add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies

7. Solaris

Add route to solaris10

Hi need to add 2 routes, one on each server. I know the route add comand but I have always been given the parameters to put in. I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ? In... (6 Replies)
Discussion started by: vettec3
6 Replies

8. Solaris

Add route to solaris 10

I need to add a new route on solaris10 machine. I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway. How I do ? Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies

9. Solaris

Couldn't add route on Solaris 10

Hi Solaris Experts, I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node # netstat -rnv IRE Table: IPv4 Destination Mask Gateway Device Mxfrg Rtt Ref Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies

10. IP Networking

Add explicit route

Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254 if not working, please try gateway through management port: 10.128.55.254 Just want to double confirm if this would be the correct command #route add -net 10.128.255.41/32 10.128.201.254 And if didnt work #route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies

LEARN ABOUT REDHAT

aggregate-ios

AGGREGATE-IOS(1)					      General Commands Manual						  AGGREGATE-IOS(1)

NAME

       aggregate-ios - optimise a concatenated set of cisco/IOS prefix filters to help make them nice and short.

SYNOPSIS

       aggregate-ios <source_config >optimised_config

DESCRIPTION

       Takes  cisco IOS configuration on stdin, and optimises any prefix filters found using aggregate(1).  Optimised filters are produced on std-
       out.

OPTIONS

       None.

DIAGNOSTICS

       Any diagnostics produced by aggregate(1) are passed through on stderr.

EXAMPLES

       The following configuration fragment:

	 ip prefix-list AS65530 description Foo, Inc
	 ip prefix-list AS65530 permit 10.1.0.0/16
	 ip prefix-list AS65530 permit 10.2.0.0/16
	 ip prefix-list AS65530 permit 10.2.1.0/24
	 ip prefix-list AS65530 permit 10.3.0.0/16
	 ip prefix-list AS65531 description Bar.Com
	 ip prefix-list AS65531 seq 5 permit 192.168.1.0/24
	 ip prefix-list AS65531 seq 10 permit 192.168.2.0/24
	 ip prefix-list AS65531 seq 15 permit 192.168.0.0/19

       is optimised as follows:

	 ip prefix-list AS65530 permit 10.1.0.0/16 le 24
	 ip prefix-list AS65530 permit 10.2.0.0/15 le 24
	 ip prefix-list AS65531 permit 192.168.0.0/19 le 24

SEE ALSO

       aggregate(1)

HISTORY

       Aggregate-ios was written by Joe Abley <jabley@mfnx.net>.

BUGS

       All those in aggregate(1) and then some :)

Joe Abley							 2000 November 27						  AGGREGATE-IOS(1)
All times are GMT -4. The time now is 04:45 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy