06-27-2005
How to List all Network cards
Hi,
I'm looking for a command to be able to list all my network cards available on my server.
With the command "ifconfig - a", I can only see to configured network card(s)
Any idea ?
Thanks a lot for your help,
Fabien
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies
2. Solaris
Hi,
I'm looking for a command to be able to disable a network card under the boot PROM.
I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0).
Thanks,
Fabien (6 Replies)
Discussion started by: unclefab
6 Replies
3. AIX
The title speaks for itself. I have never attempted this but understand there is a way to use two network cards (en0 and en1) with the same IP address so as to load balance the traffic flow through both cards. Anyone know the answer? (4 Replies)
Discussion started by: johnf
4 Replies
4. Solaris
Hi all,
I have a server running with Solaris and I have 2 Pci cards installed on this server (since a while), 1 with 4 coppers connections output and one with a Fiber network connection output.
Today, this server is using the on board network connection (Ce0).
How can I find the other... (7 Replies)
Discussion started by: unclefab
7 Replies
5. Solaris
Hi All,
Hope you are all doing good.
In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe... (3 Replies)
Discussion started by: Krrishv
3 Replies
6. Solaris
Hi all
I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem.
So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1).... (2 Replies)
Discussion started by: sbk1972
2 Replies
7. Programming
Hello
I have a problem with retreiving network interface list using IOCTLs. I have 4 interfaces:
$ ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope... (1 Reply)
Discussion started by: xyzt
1 Replies
8. Hardware
Hello everybody,
I'm having troubles with Slackware 13.1 and network cards.
I have one on-board Ethernet card (which is recognized and works okay) and a PCI Ethernet card (which is also recognized, but doesn't appear in 'ifconfig -a'). If i run a 'lspci', i can see the kernel recognized the... (5 Replies)
Discussion started by: semash!
5 Replies
9. UNIX for Dummies Questions & Answers
Hi All,
I have just setup a webserver running on a linux box. This server has 2 ethernet cards and only 1 is in used now. eg. 192.168.10.1 is my server IP. All users from 192.168.10.X can access my webserver. However, users from another LAN 10.10.10.X are not able to access my webserver. They... (0 Replies)
Discussion started by: jackma
0 Replies
10. Solaris
Hello All
I am trying to get a list of process or applications runninging on the network only. I should emphasize that im not interested in the application or process if its not using the network.
I tried the good old netstat comand, but im not able to figure out how to list the running... (8 Replies)
Discussion started by: busi386
8 Replies
LO(4) BSD Kernel Interfaces Manual LO(4)
NAME
lo -- software loopback network interface
SYNOPSIS
pseudo-device loop
DESCRIPTION
The loop interface is a software loopback mechanism which may be used for performance analysis, software testing, and/or local communication.
As with other network interfaces, the loopback interface must have network addresses assigned for each address family with which it is to be
used. These addresses may be set or changed with the SIOCSIFADDR ioctl(2). The loopback interface should be the last interface configured,
as protocols may use the order of configuration as an indication of priority. The loopback should never be configured first unless no hard-
ware interfaces exist.
The loopback interface lo0 is created at boottime, it always exists and cannot be destroyed with ifconfig(8). Additional loopback interfaces
can be created by using the ifconfig(8) create command.
DIAGNOSTICS
lo%d: can't handle af%d . The interface was handed a message with addresses formatted in an unsuitable address family; the packet was
dropped.
SEE ALSO
inet(4), intro(4), ifconfig(8)
HISTORY
The lo device appeared in 4.2BSD.
BUGS
Previous versions of the system enabled the loopback interface automatically, using a nonstandard Internet address (127.1). Use of that
address is now discouraged; a reserved host address for the local network should be used instead.
BSD
September 3, 2006 BSD