network interface questions Post: 7301

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

2. Linux

Hello everybody, How can link network interface to the output of lspci -vv. Basicly i need to know who is the manufacturer of a specific interface, for example eth0 {Is it an Intel, or Broadcome, or something else}. Is there a way to find that out? Thanx

3. Solaris

Network Interface Issue

Hi all, Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP. - - - -- --...

4. Solaris

Network interface configuration

Dears, i follow this to configure Network interface for my PC O/S : Unix Sun Solaris vi /etc/hostname.bge0 and write my ip vi /etc/netmasks and write my subnetmask vi /etc/defautrouter and write my gatwey vi /etc/resolv.conf and write my DNS after i reboot My Computer ...

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

6. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

7. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT X11R4

inet_type

inet_type(4)                                                       File Formats                                                       inet_type(4)

NAME

       inet_type - default Internet protocol type

SYNOPSIS

       /etc/default/inet_type

DESCRIPTION

       The inet_type file defines the default IP protocol to use. Currently this file is only used by the ifconfig(1M) and netstat(1M) commands.

       The  inet_type  file  can  contain  a  number of <variable>=<value> lines. Currently, the only variable defined is DEFAULT_IP, which can be
       assigned a value of IP_VERSION4, IP_VERSION6, or BOTH.

       The output displayed by the ifconfig and netstat commands can be controlled by the value of DEFAULT_IP set in inet_type file.  By  default,
       both commands display the IPv4 and IPv6 information available on the system. The user can choose to suppress display of IPv6 information by
       setting the value of DEFAULT_IP.  The following shows the possible values for DEFAULT_IP and the resulting ifconfig and netstat output that
       will be displayed:

       IP_VERSION4     Displays only IPv4 related information. The output displayed is backward compatible with older versions of the ifconfig(1M)
                       and netstat(1M) commands.

       IP_VERSION6     Displays both IPv4 and IPv6 related information for ifconfig and netstat.

       BOTH            Displays both IPv4 and IPv6 related information for ifconfig and netstat.

       The command-line options to the ifconfig and netstat commands override the effect of DEFAULT_IP as set in the inet_type file. For  example,
       even if the value of DEFAULT_IP is IP_VERSION4, the command

       example% ifconfig -a6

       will display all IPv6 interfaces.

EXAMPLES

       Example 1: Suppressing IPv6 Related Output

       This is what the inet_type file must contain if you want to suppress IPv6 related output:

       DEFAULT_IP=IP_VERSION4

SEE ALSO

       ifconfig(1M), netstat(1M)

SunOS 5.10                                                          16 Jun 1999                                                       inet_type(4)

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Discussion started by: witt

2. Linux

Get info on network interface

Discussion started by: aleksey